Search:

Type: Posts; User: gsxrsquid

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. X2

    X2
  2. Replies
    67
    Views
    2,620

    Yep, that's why we use this site. What we do in...

    Yep, that's why we use this site. What we do in the south might not be so good in the north.
  3. Replies
    67
    Views
    2,620

    I kill red for same reason. If it doesn't work at...

    I kill red for same reason. If it doesn't work at all they call for help. If you have a pan full of water in the winter you REALLY need a tech.
  4. Replies
    22
    Views
    1,048

    I have used some of the heat absorbing gels and...

    I have used some of the heat absorbing gels and they work pretty good. IF I don;t have to worry about drips i prefer a wet rag though.
  5. Replies
    11
    Views
    1,110

    funny thing, Right now I have the same model at...

    funny thing, Right now I have the same model at another facility doing this same thing. The top bearing IS bad on this one.
    Since I first posted this a couple years ago I have had to repair at...
  6. follett has a nice overhaul kit for their...

    follett has a nice overhaul kit for their machines too. You can get the evap, auger, bearings, evap drain pan and hardware even a new water supply tube for about $1500 for the L400 and less for the...
  7. Replies
    1
    Views
    304

    Follett LC 12 part needed

    I can find the installation/parts manual on the follett site but cannot find the seperate parts break down. I need either the detailed parts bulletin or the part number for the main drain that runs...
  8. Does Follett maker a quiet ice maker/dispenser?

    We have a patient area in the hospital that gets a lot of traffic becasuse of the ice machine. It is a countertop LC12 follett machine. The room is small and noise is a big factor.
    Does anyone...
  9. Replies
    2
    Views
    343

    Thanks!

    Thanks!
  10. Install the clock and walk away from the cooler. ...

    Install the clock and walk away from the cooler. :)
  11. Replies
    24
    Views
    1,447

    what they said. Sometime the users like to...

    what they said. Sometime the users like to prop the doors open because it is so cold in there (go figure) In humid areas you can frost up quick that way. Recently I have had a rash of defrost...
  12. Replies
    2
    Views
    343

    hoshi DCM-240BAF

    Does anyone have the parts list for this machine? I went to the Hoshi site and kept getting a message that there is no such machine. I was able to get the service manual but not the parts...
  13. Replies
    20
    Views
    2,672

    it is mud or iron deposits?

    it is mud or iron deposits?
  14. Replies
    15
    Views
    2,460

    aww that hoshi is almost clean. you don;t even...

    aww that hoshi is almost clean. you don;t even have any frogs living in it. :grin2:
  15. Replies
    2
    Views
    406

    Follett 25CT 400A icemaker question

    I have worked on smaller Folletts before but this is the first time I worked on this model. 18 months old and never cleaned. Mostly iron and calcium deposits. I get everything shiny and clean and...
  16. Replies
    8
    Views
    612

    Yep it was low on charge all right. Both cap...

    Yep it was low on charge all right. Both cap tubes from the TXV had been rubbing together near the sensing bulb and the bult lost it's charge and then the wear caused the machine charge to slowly...
  17. Replies
    8
    Views
    612

    SH was over 50 and SC was about 3

    SH was over 50 and SC was about 3
  18. Replies
    8
    Views
    612

    whoever installed it left the cap off the liquid...

    whoever installed it left the cap off the liquid line service port so I am hoping that is where the gas went.
  19. Replies
    8
    Views
    612

    thanks! I found that out. NOTHING on the site!

    thanks! I found that out. NOTHING on the site!
  20. Replies
    19
    Views
    2,350

    until you get a breath of it.

    until you get a breath of it.
  21. Replies
    14
    Views
    3,018

    I bought a hydraswage years ago and it has paid...

    I bought a hydraswage years ago and it has paid for itself time and again. with that and a ratchet tubing bender I replaced a few reversing valves with fewer joints and looked better too. I want...
  22. Replies
    5
    Views
    2,024

    I have one just like it in the house I bought in...

    I have one just like it in the house I bought in SE Mo. must be a state thing. :)
  23. Replies
    56
    Views
    10,914

    that's no lie. I had one ike that. person...

    that's no lie. I had one ike that. person worked at the animal shelter. when they were supposed to put down a dog or cat they brought them home. 3 bed room shouse all beds rooms full of animals...
  24. Replies
    14
    Views
    1,212

    why would you even put guages on a package unit...

    why would you even put guages on a package unit unless you thought something was wrong and had exhausted all the other possibilities?
  25. Replies
    19
    Views
    2,350

    Yeah, they said the same thing when R22 came in...

    Yeah, they said the same thing when R22 came in and started replacing R12. I don't know what is available commercially but the new big refrigerant should be CO2.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event