Search:

Can anyone tell me what "normal" combustion analysis readings would be for propane. Literature I have is for NG and fuel oil. Propane not as common around here.
Thanks

If you go to commercial.carrier.com the Installation, Operation, and Service Manual is able to be downloaded. Go to "literature", which will direct you to a screen where you can enter the model...

the easiest thing to do would be to get a Trane zone sensor module from a Trane distributor. The numbered terminals in the zsm (stat) match the numbers in the unit.

If the Comfort Manager is dead and you want to use a thermostat;
you would need to use balancing dampers for the zones, drive the zone dampers open or remove and balance the system airflow. Also...

if you have or can get a sporlan product cd, there is a product selector with a piping system. If the piping is clicked on, you get a window wanting system info, including refrigerant, pipe length,...

can anyone advise or give resources for greenhouse ventilation/temperature/humidity control?

Greetings Is there a reliable formula for self-employment success. I'm about ready to go it alone; preferably process/commercial refrig only. Any input from small shop or loners welcome. I've...

the barometric -necessary. go to beckettcorp.com product lit is available by using "prof" and "info":user name and pswd. cf500 pdf shows firebox pressure at .04

UA all the way LU94 canton oh

try http://www.fireye.com for literature/troubleshooting info. I had this problem last winter, changed the scanner and the problem was gone. Fireye tech support informed me that the scanner tube is...

be careful scanner voltage is very high (like 500 volts) if scanner looks like it is glowing it is probably bad. when scanner sees uv or infrared voltage is conducted across electrodes.

gas valve is made by siemens and works at negative pressure. top plate unscrews to reveal adjustment screws for high and low fire(bias). Trane only gives combustion requirements in their manual,...

does anyone have an internal wiring diagram for 33zct55,56, or 57. having slight disagreement with management whether or not override button is programmable. ACI's site does not show internal...

greetings fellow trane lovers??!! an '89 vintage rtha255 I take care has this past few weeks been making a strange surging/growling noise. I checked dis supht per IOM, found it high so I added...

for dimensions, try contacting a rebuilder like national compressor, or uri

got e-mail add or fax? I could send you pdf's for 3-12 ton and 12-25 ton carrier info from hvacpartners.com

what advantages are there for working "factory service" (york,trane,carrier,mcquay?) vs. for a mech contractor? I'm thinking about making a move but have doubts over the issue. (presently working...

What is an evaporator coil (ac) or indoor coil (hp) rated for pressure with r410a? our training center is having a safety class, and we have conflicting info. tks

depending on actuator brand, honeywell and johnson make signal adapters

I teach at our local jatc school, and was going to use it for teaching/troubleshooting. a little expensive, so I need to consider options

Has anyone used Johnson's Commissioning tool? Is it worth buying? If so, what would I expect to pay? I have a Kele 0-10vdc, 4-20 ma tool. Thanks for any info.

I work for a contractor that installs and services quite a few, and went to factory school. Set-up, start-up very important. 50% excess air very important, and I have seen and replaced a bad burner...

we use a program called PROCOMM ; in this program "alt P" allows for change of baud rate, comm port, etc. in my experience hyperterminal also works as well

at a previous contractor I worked for, 3 were installed at a new manufacturing building. YORK did schooling for us at our shop, certified us for start-ups, service, etc. The 3 there were constant...

sparks, i'm an instructor @ our local and presently teaching burners. Can I get this Powerburner book? see profile for info