Search:

Type: Posts; User: bigsky2011

Search: Search took 0.01 seconds.

  1. Replies
    29
    Views
    1,693

    Always a fun time working in a mobile home. From...

    Always a fun time working in a mobile home. From repairing to installing, lots of funny stories to be told.
  2. Replies
    29
    Views
    1,693

    Boilerman.. Yes I pull the cover off, It is the...

    Boilerman.. Yes I pull the cover off, It is the only way to properly clean out furnace. Yes the studs do snap off from time to time. When done I anti seize them with the copper colored anti seize. I...
  3. Replies
    29
    Views
    1,693

    Lots and lots of Miller oil furnaces here in Pa....

    Lots and lots of Miller oil furnaces here in Pa. . Excellent furnace. Easy to clean and service.
  4. Sounds like a wiring issue. Heat pump thermostat...

    Sounds like a wiring issue. Heat pump thermostat used?? Proper 24v wiring to units? What about the plug on the goodman ahu-- what wires are there for you to connect to??
  5. Replies
    11
    Views
    1,251

    It is any ecm motor I believe, that the whole...

    It is any ecm motor I believe, that the whole motor needs replaced. It is not only goodman. I try to stay away from the ecm, but it is hard to, with the high s.e.e.r. nowadays.
  6. Replies
    33
    Views
    3,641

    I have an e-250 service van, truck with lift...

    I have an e-250 service van, truck with lift gate, and e-350 cube van with lift gate for installs.
  7. 7/8 sounds more like it.. 1 1/8 for 20 ft --4...

    7/8 sounds more like it.. 1 1/8 for 20 ft --4 ton--- probably not..
  8. Replies
    8
    Views
    1,656

    My fry daddy works just fine,,, about 3 yrs. and...

    My fry daddy works just fine,,, about 3 yrs. and still cookin
  9. Replies
    99
    Views
    13,700

    Years ago fresh out of school, while changing and...

    Years ago fresh out of school, while changing and oil filter on a tank. The little top air bleeder screw came flying out while bleeding air out of it. I could not find it and panicked, went to van...
  10. Replies
    23
    Views
    1,890

    As an owner, I want the guy who can troubleshoot...

    As an owner, I want the guy who can troubleshoot and diagnosis the problem. Parts changers cost your business more in the long run. You will eventually lose your customer. I am here for my customers...
  11. Replies
    28
    Views
    1,866

    I have to agree with everyone else about 60 to 70%

    I have to agree with everyone else about 60 to 70%
  12. I should have said, When it is important I use...

    I should have said, When it is important I use the scale...always. When I am working on refrigeration units with sight glass and I see a small amount is needed to fill glass, I do not use scale.
  13. I use one when pulling charge on unit for repair....

    I use one when pulling charge on unit for repair. repair, then weigh charge back in. when adding refrigerant in longer linesets after install, most definitely. When I top off units that are a little...
  14. Replies
    16
    Views
    2,512

    Hey now that is funny.... I have been outbid by...

    Hey now that is funny.... I have been outbid by guys that drive those kind of vehicles.... funny...,,, though... one time I was called back to fix this kind of guys shoddy work. Oh did I make...
  15. Replies
    48
    Views
    4,198

    I have not seen a lot of bad goodman coils over...

    I have not seen a lot of bad goodman coils over the years. lately or otherwise. what is the model??? Where is the leak located on all these bad units????
  16. Replies
    6
    Views
    690

    my hats off to fieldpiece too. good customer...

    my hats off to fieldpiece too. good customer service when i had problem with meter.
  17. Replies
    10
    Views
    2,284

    nice video

    nice video
  18. Replies
    8
    Views
    1,995

    That is some nice gadget. I will have to make me...

    That is some nice gadget. I will have to make me one up.
  19. Replies
    25
    Views
    5,803

    Nice, neat job

    Nice, neat job
  20. Replies
    22
    Views
    1,932

    take note of what stonewallred posted. he is 125%...

    take note of what stonewallred posted. he is 125% right. keep your van clean and forget the big advertisements, newspaper, yellow pages, ect. They did not work for me. Good work ethics, hard, honest...
  21. Replies
    9
    Views
    763

    get a good contractor and referenances from...

    get a good contractor and referenances from clients. Good installations are most important. Big brand name not so much.
Results 1 to 21 of 22
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event