Search:

Type: Posts; User: SinCityKid

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    40
    Views
    5,124

    All that, and i'll bet all the customer needed...

    All that, and i'll bet all the customer needed was a run cap. hahaha
  2. Replies
    15
    Views
    801

    Wheel appeared fine. Straight. No vibration.

    Wheel appeared fine. Straight. No vibration.
  3. Replies
    15
    Views
    801

    Yes. It is a GCS16. Sorry, typo. Anyhow yes...

    Yes. It is a GCS16. Sorry, typo. Anyhow yes the nameplate calls for a 3/4 hp motor. I removed a Century 3/4 hp 1075 3 speed motor rated for 4 amps. I don't know what was in it before that.
  4. Replies
    15
    Views
    801

    Blower Motor Failures

    No cool call at a hair salon. Failure was the blower motor. Unit is a Lennox GCS18-060-75-4Y. Customer stated that she has been at this location for 3 years and has had to replace this motor every...
  5. Replies
    11
    Views
    2,712

    That dip in the condensate line serves as the...

    That dip in the condensate line serves as the trap.
  6. Replies
    26
    Views
    3,013

    Yup!

    Yup!
  7. Replies
    26
    Views
    3,013

    New way to save 1000's on your power bill!

    I took this picture while standing on a busy sidewalk! It must be safe though, green wire is only a ground right? pfft...
  8. Replies
    17
    Views
    2,704

    It may not have been internally insulated, but it...

    It may not have been internally insulated, but it is now.
  9. Replies
    7
    Views
    1,410

    That was the norm here for several years, 2...

    That was the norm here for several years, 2 story's usually have piss poor access. Very scary some of the time. I have turned jobs down because of it.
  10. Replies
    3
    Views
    447

    Advise for new gauges...

    I just bought a set of digital gauges. SMAN-4. I also got a set of hoses with the ball valve shut off. I have always carried two sets of analog gauges, one for r-22 and one for 410a. Both with low...
  11. Replies
    13
    Views
    1,003

    I appreciate all the responses. That gives we a...

    I appreciate all the responses. That gives we a lot to look at & consider. I understand how poor airflow would affect efficiency but could somebody explain how it would cause compressor failure?...
  12. Replies
    13
    Views
    1,003

    Shorted compressor question

    I had a call yesterday where a 2 year old 410a compressor was shorted to ground (Trane XB13). I checked it at the compressor terminals. It is a 5 ton split unit (cool only). I donít have any history...
  13. Thread: candle soot

    by SinCityKid
    Replies
    16
    Views
    1,108

    Electric candles ...

    Electric candles

    http://www.batteryoperatedcandles.net/
  14. Replies
    13
    Views
    3,888

    Go home A/C, your drunk

    Came across this condenser the other day. Homeowner said he backed into it with a backhoe 9 years ago. Said he has never had 1 problem with it and it worked well. I was there to work on the other...
  15. Replies
    7
    Views
    801

    ahhh. that makes sense. Thx

    ahhh. that makes sense. Thx
  16. Replies
    7
    Views
    801

    Fan motor mystery???

    I went to a no cool call yesterday. 5 ton ICP heat pump split unit. Owner said that nothing was running on the condensing unit so he hit the top of it with his fist and the fan began to run but not...
  17. Replies
    9
    Views
    866

    I'm not going to move it. But for my educational...

    I'm not going to move it. But for my educational sake isn't the high side pressure the same between the compressor and the metering device +\- a couple psi?
  18. Replies
    9
    Views
    866

    So just cut the old one out and sweat in a...

    So just cut the old one out and sweat in a Schrader valve for the Mars option? PITA for a simple valve. Thanks for the info though!
  19. Replies
    9
    Views
    866

    It is running like that. We have highs of 112 and...

    It is running like that. We have highs of 112 and lows at night are 95 so my options are limited. I like your suggestion of tapping into the service port for a temporary pressure switch and I will do...
  20. Thread: Microfarads

    by SinCityKid
    Replies
    12
    Views
    1,035

    Microfarads

    Can anyone please explain to me exactly what a microfarad is and it's relationship to PSC motors and run caps in plain English. I know how to measure them on caps and match them to motors but that...
  21. Replies
    9
    Views
    866

    Pressure switch question...

    4 ton straight cool York condenser. 410a

    Mod#TCGF48S41S1A

    Ambient hit 112 last Saturday and unit shut down. When I got there I noticed the high pressure switch was open. Attached gauges and...
  22. Replies
    26
    Views
    5,426

    What problem did this cause that couldmt be...

    What problem did this cause that couldmt be covered by waranty?
  23. Replies
    5
    Views
    1,255

    condiot is conduit is conduit...

    Stopped for some Mexican food in San Diego. Looked up and saw this. For what it's worth the food was fricken delicious!

    369081369091369101
  24. Replies
    1
    Views
    725

    Help with Lennox condensing fan motor

    I need help determining the proper OFM & blade for 2 identical Lennox condensers (straight cool). I have a job at a bank repossessed house and someone stole both of the condensing fan motors and fan...
  25. The cap looks like it woulda fit right back in...

    The cap looks like it woulda fit right back in the hole.
Results 1 to 25 of 68
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event