Search:

Type: Posts; User: jtrammel

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds; generated 26 minute(s) ago.

  1. Replies
    9
    Views
    300

    Rags and mastic.

    Rags and mastic.
  2. Thread: CO detecters

    by jtrammel
    Replies
    4
    Views
    174

    Cracked heat exchangers rarely spill CO into the...

    Cracked heat exchangers rarely spill CO into the air stream.
  3. Shouldn't need a second meter with the UEI. It's...

    Shouldn't need a second meter with the UEI. It's always good to have a back up though. the amprobe 51NAV is on my tool wish list. I have a uei dl379, FP hs36 and fluke 902 on the truck.
  4. Replies
    16
    Views
    481

    1st response just fixed a 100 ton chiller with...

    1st response just fixed a 100 ton chiller with these tools. Didn't even need them though. Just had to reset a pump starter. 512491
  5. Replies
    17
    Views
    676

    https://www.trutechtools.com/Vacuum

    https://www.trutechtools.com/Vacuum
  6. Replies
    17
    Views
    676

    With your pump I'd get 1- 1/2 " hose with 1/4"...

    With your pump I'd get 1- 1/2 " hose with 1/4" and 1/2" ends and 1-3/8" or 1/2" hose with 1/4" ends. 2- vcrts and go directly to pump. Micron guage on the side port of one of the vcrts.
  7. If you have to have fluke the best they got in a...

    If you have to have fluke the best they got in a single meter for HVACR is the 902 or the 322/116 combo.
  8. http://www.amprobe.com/amprobe/usen/Clamp-Meters/I...

    http://www.amprobe.com/amprobe/usen/Clamp-Meters/Industrial-Navigatorô-Clamp-Meters-/AMP-ACD-51NAV.htm?PID=73092
    ...
  9. Replies
    12
    Views
    240

    These are great for gas line and condensate...

    These are great for gas line and condensate lines.
    http://www.ereplacementparts.com/118-spline-shank-spline-shank-cutter-hammer-drill-bit-drill-p-193815.html
  10. You'll need another meter too since that one...

    You'll need another meter too since that one doesn't do a lot of the other functions you'll need as a service tech.
  11. Replies
    12
    Views
    240

    It pays for itself fast. We used to have a hilti...

    It pays for itself fast. We used to have a hilti and the motor burnt up. We went a year or so Before buying the hitachi and in the meantime we used black iron pipe and a sledgehammer. Talk about a...
  12. Replies
    16
    Views
    481

    I don't have a pic but I usually take a 6-in-1,...

    I don't have a pic but I usually take a 6-in-1, channel locks, fphs36 and digicool ak900 and iphone. If I find a problem I go get my service bag or whatever else I need for repair.
  13. Replies
    5
    Views
    160

    This is all I could find on that...

    This is all I could find on that http://www.appliancedesign.com/articles/83147
  14. Replies
    5
    Views
    160

    I don't think carrier/UT owned them they just...

    I don't think carrier/UT owned them they just partnered with them. Not 100% sure on that though. I know in our area carrier was trying to push aeroseal on their dealers a while back. There's only 2...
  15. Replies
    12
    Views
    240

    Poured solid concrete about 5-10min and...

    Poured solid concrete about 5-10min and brick/hollow block 1-2 minutes.
  16. Replies
    12
    Views
    240

    This...

    This http://www.nailgundepot.com/Hitachi-DH38YE-112-Rotary-Hammer-Drill-wCase-Details.html?gclid=Cj0KEQjw-dSgBRDb0oOl9MzxqMEBEiQAkHqy-ZfizLkfjeLHtFiAq6SmGfiZeWDlxz5n3N3YiOb66RMaArah8P8HAQ
    And this...
  17. The top plate is at the top of the wall. A high...

    The top plate is at the top of the wall. A high sidewall register should be about 6" below the top plate.unless you're coming down from above, then ceiling registers would be a better choice.
  18. Replies
    12
    Views
    354

    Yea but a crisp $100 bill works best.

    Yea but a crisp $100 bill works best.
  19. Replies
    43
    Views
    1,444

    I'm bad about changing mine too mines a 5"...

    I'm bad about changing mine too mines a 5" aprilaire so I don't have to worry about it much.
  20. Replies
    82
    Views
    3,089

    Dope... I only put one p in appion. Thanks.

    Dope... I only put one p in appion. Thanks.
  21. Replies
    41
    Views
    898

    Well I prefer to stay out of the blah blah...

    Well I prefer to stay out of the blah blah corporate world. I don't want to wait 3-6 months for payment anyway.
  22. Replies
    41
    Views
    898

    I don't know too much about 3rd party commercial...

    I don't know too much about 3rd party commercial maintenance blah blah blah. If I go on a commercial unit and the sheave, pully, bearing etc is worn/broken I change it and send them a bill I've never...
  23. The metering device is in the outdoor unit. Both...

    The metering device is in the outdoor unit. Both lines on a minisplit are on the low pressure side of the system. They should both be cold and insulated.
  24. Replies
    2
    Views
    139

    I would do a 2 stage daikan with propane...

    I would do a 2 stage daikan with propane auxillary.
  25. Replies
    82
    Views
    3,089

    I tried emailing Christian with the email address...

    I tried emailing Christian with the email address in his profile and the email address isn't valid.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event