Search:

Type: Posts; User: motec

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    849

    Check page 149 of FX user guide, the...

    Check page 149 of FX user guide, the configuration you are trying to upload may be protected.
  2. Thread: York BAS

    by motec
    Replies
    16
    Views
    2,387

    Thanks for all the replies. The job is in...

    Thanks for all the replies. The job is in Michigan and also 1 building was integrated over from Network 8000 the othe buildings were pnuematic and the used transducers on all actuation. The controls...
  3. Thread: York BAS

    by motec
    Replies
    16
    Views
    2,387

    York DDC

    What I am looking for is information on a propritory automation system that York was installing in Buildings.
  4. Thread: York BAS

    by motec
    Replies
    16
    Views
    2,387

    York BAS

    Does anyone have any information on york ddc systems that was installed by York offices? I am looking into a complex of buildings with their system in and would like to gather as much info as...
  5. Replies
    18
    Views
    5,052

    I agree with Quicktec as I had worked for many...

    I agree with Quicktec as I had worked for many years with the Tempmaster Line of diffusers and if engineered and applied properly you will not have any draft complaints.
  6. Replies
    281
    Views
    41,015

    Thanks for the reply. Yes to all, as I may have...

    Thanks for the reply. Yes to all, as I may have to modify the asd controls.
    When connecting to the GCM or LCM with hyper terminal are you connecting
    to the the 25 pin connection as a direct...
  7. Replies
    281
    Views
    41,015

    Correct it is the old Barber Coleman. Price book...

    Correct it is the old Barber Coleman. Price book lists two part numbers
    LAPT-80800-EPSI
    LAPT-80800-PSI
  8. Replies
    281
    Views
    41,015

    Network 8000 software

    What software is required to make changes to Network 8000 controllres
    eg.MZ2-1 controllers
  9. Replies
    20
    Views
    5,727

    I copied ftp.buildingautomationforum.com and then...

    I copied ftp.buildingautomationforum.com and then pasted it to my browser then entered sign on and password without no problems. If I try to open the stencils from hvac-talk I get a blank visio page...
  10. Replies
    20
    Views
    5,727

    Just posted 3 stencils, let me know if they open....

    Just posted 3 stencils, let me know if they open. On codewriters I had to move them to Visio and they worked fine.
    Mike
  11. Replies
    10
    Views
    1,809

    How about a posting of all available visio...

    How about a posting of all available visio stencils member would like to share!
  12. Replies
    4
    Views
    1,243

    Teletrol has 2 lines of controllers one is bacnet...

    Teletrol has 2 lines of controllers one is bacnet which is the E Building line. The second and older line which is the Integrator line is not.
  13. Replies
    4
    Views
    1,243

    Are their any drivers or gateways available?...

    Are their any drivers or gateways available? Customerwould like to integrate to Tridium.
  14. Thread: Visio Stencils

    by motec
    Replies
    39
    Views
    9,528

    Visio Stencils

    Does anyone have any JCI controller stencils they would be willing to share? I hate to start from scratch and then find out someone has them.
  15. Replies
    78
    Views
    7,834

    JCI contractor Purchases

    I am in the Detroit area and rumors are flying about JCI purchasing more contractors. Is this happening all over and what has been the fall out?
  16. Replies
    19
    Views
    2,181

    I was told that Computrols has a visio set of...

    I was told that Computrols has a visio set of graphics similar to Prographics
Results 1 to 16 of 16
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event