Search:

Thanks for the feedback Yall. I had my fit test this week and was just wondering. I never wear the thing. I turn on the vents and set a fan if I can.

Out of curiosity, how many of you wear your 123 respirator?

OP asks a loaded question-the process of pulling both heads requires a working knowledge of that job-such as water quality, tower quality,and biological debris. (i used to pull both heads on some...

Better be careful Fabregas, You may be jcis next lawsuit,since that seems to be the only way they can stay in business is to sue their ex collective bargaining units.

steveoo, total charge is 321#. leaks repaired, evacuated and charged, running good now.

Update-was able to return-started pulling charge with the intent to change oil sensor-found circuit 270# low on charge. pressureized and found leak at suction coupling coming off evap. This is a...

nice looking job. Ive been involved in one so far

You may be able to contact Baltimore Parts and order the info you need. I say this because they have emailed updated service lit to me upon request. Might be worth a try.

Find a local farm boy or check with your local vocational education program. I'm on the advisory board of our local public vo-tech school and we always have potential employers knocking on the door...

oil heater is ok. I have some other things that need quoted for this job and wont get back till the approval. I will update then.

welcome to the UA. Local 520 here.

the sensor is a Henry. I am assuming it is a level sensor.

Model # AGS250B27-ER10
On start up circuit 2 runs about 40 seconds and alarms on low oil level. oil level in bottom glass of separator is full and at bottom of top glass during short run time. oil...

Is this a post about ex mcdonalds employees or managers :cheers:

Thanks for the update.

check your auxiliaries. I had the same senario once and it drive me crazy till I found it.

Here-YORK PA

We the mechanics in the Harrisburg branch already went through service simplification-We all left jci and the work followed us. IMAGINE loyalty to the mechanic and not the empire

Dont forget the unpaid day in the street for half of the crew(which by the way were all legacy YORKIES), even though we had just completed the TMI job and we all had scheduled work.

I think your coworker received the sevice lit from one of his ex co workers upstate

Thanks from all of us Richard. Well said. Thank You for leading the way for guys like me.

Nice post Richard. Thank You. I am almost looking forward to my next teardown. P.S. It was fun to get DD riled up.

t2,
after reading this post and your other one, I wonder what your boss and your customer are doing to protect you from the 123 hazards. There is only one way to fix this machine and if your boss...

You should have seen them in the lab after the explosion. Have to agree, the product was rushed to market.

Used my first two piece tube plug today. I have always used just the plug in the past with good success. Any thoughts on the two piece would be appreciated.
Thanks

Sorry it took me so long TGL, Tis the teardown season. The scroll drew locked rotor and blew B phase fuse. Replaced comp and fuse and ran. I was able to find that this size comp is dependant on a...

I received the new comp. and tried across the line-no go replaced comp and ran fine. still trying to contact Danfoss for their instructions on this. If I do I will keep you posted. Thanks

please expand on your thoughts for across the line start. I would appreciate any info for our science project before I go through with it.

I am supposedly getting the new comp. Friday. This is a Danfoss installed in an Annexair package mod. The factory says do not apply 60 Hz across the line, They claim the windings wont take it since...

Thanks for the whacking idea Flange. I tried it and as usual my arms got tired:censored: I guess Danfoss is sending me another comp.. Thanks for you alls input.

due to the normally low starting frequency, i am afraid that if i applied 480 60 hz the windings would fry, but i have thought about it bg420.

just manual, no bypass

I have a Danfoss vsd scroll comp that faults on error code A18 @ startup, I think this is indicative of a blocked scroll and comp not reaaching min speed, but I dont know how to prove comp or drive...

ut-oh

In the end when these SOBs are telling me to stay home so they can make their numbers.........Well that just about says it all. I am a married man with two young children. I wake up and go to work...

cool hand luke shows the human will to never quit through the whole movie. one of the best of all time.

Is there a chemical feeder on the market that can sense glycol concentration and automatically feed. Any ideas appreciated. Thanks

I am extremely proud to have had the good fortune of working for YORK. I am extremely HAPPY I no longer work for johnson controls.(12 large tonnage mechanics in 14 months now gone)

I keep my U-Tube close to me. I know it won't lie. I am also waiting for a couple of absorbers to be demoed so I can rescue the Merriams and give them a good home to ease their way into...

heck, they'll soon be giving it away.

ALC is just a plug and play to take over a metasys system.

Hats off to Mike Rowe. Its nice to know that there are some people of influence with common sense who have our backs. Bring back the textile industry, bring back the steel industry, and let AMERICAN...

I always clean the sensors during winter work. It seems to minimize the problems. Thanks for the tip on the sensitivity screw.

we bought our Holland Grill twelve years ago. I love the fact I can put a turkey on it and walk away-just open the lid three hours later. I have never had a flare up problem with the Holland. Once in...

and remember, everything begins and ends with flow.

your flow is higher than design. the number in the panel sales order screen is feet of head. get a correct delta P with one guage and multiply by 2.3 for feet of head.like 56 says, to achieve design,...

AMEN. I spent my apprenticeship with YORK and personally witnessed jci screw too many customers and blame it on us the mechanics. I now work for the competition at their request and have found life...

NOPE. not going to do it.

123? I am taking a popular line from the site. "I will not say what I want to"

Fortunately jci kept some of the key people in the engineering group such as KB, BH, DD, MG, and a couple of others who have given their all to create a top of the line product. These guys have...