Search:

Type: Posts; User: marylandtech

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    41
    Views
    1,885

    I have had this same issue with Trane commercial...

    I have had this same issue with Trane commercial air handlers. As stated clean the coil with a detergent base cleaner like triple D. I have also installed a fan off time delay to run the blower 3-5...
  2. Replies
    6
    Views
    665

    Thanks for the info! What type of complications...

    Thanks for the info! What type of complications could I have??. I was going to seal the pipe to keep water out and oversize the conduit to have additional free space around the piping. Is that enough?
  3. Replies
    6
    Views
    665

    Trane refrigerant piping length

    I have a 5 ton XL 16 I heat pump with a TAM060C Air handler R410a that I will be installing. Where can I find the maximum lineset lengths and correct sizes allowed for this unit. Someone told me...
  4. Replies
    228
    Views
    43,004

    08-10 (I think, it was all a blur lol) Good $$$...

    08-10 (I think, it was all a blur lol) Good $$$ though
  5. Replies
    228
    Views
    43,004

    wonder which ones they lost. I still see one of...

    wonder which ones they lost. I still see one of the guys from when I worked there, I'll have to ask him. Always seemed to me they were one big contract loss away from disaster all the time. They...
  6. Replies
    9
    Views
    2,253

    anybody???

    anybody???
  7. Replies
    228
    Views
    43,004

    It was the same in Maryland also (Nextech NE)

    It was the same in Maryland also (Nextech NE)
  8. Replies
    9
    Views
    2,253

    Smoker Newbie

    So Im looking to buy a reasonably priced smoker for ribs and maybe some roasts. Whats the best kind. Gas seems like it would be the easiest to maintain temps with but how is the quality of the food...
  9. Replies
    6
    Views
    1,134

    Thanks for info so far Rundawg. What does York...

    Thanks for info so far Rundawg. What does York use the 60 and 66 terminals for on the indoor circuit board that go to the outdoor unit. I think this may be part of my issue. The outdoor unit was...
  10. Replies
    6
    Views
    1,134

    Yes please email me what you have and I will...

    Yes please email me what you have and I will compare it. Thanks for the info so far. The unit is not very complicated I just want as much info as I can as this job has been "under the microscope"
  11. Replies
    6
    Views
    1,134

    Need schematic for York unit

    I have an older air handler that I'm trying to find a schematic for. Model # appears to be a F1CP030406a although it is not very easy to read. Appears to be late 80's early 90's era. Mainly need a...
  12. Replies
    35
    Views
    3,381

    Thats a great point that for some reason I...

    Thats a great point that for some reason I overlooked. But true that I am dumping "untreated " water into the boiler. Although Im sure it is not there long before it is "diluted" with the treated...
  13. Replies
    35
    Views
    3,381

    I see it all the time. When you drain a large...

    I see it all the time. When you drain a large boiler for inspection you can use the feed to refill the boiler on initial startup. Otherwise you will have to fill with your pump from the condensate...
  14. Replies
    3
    Views
    644

    Retapping threads

    So I have a Burnham 11 section cast iron sectional boiler thats a bolt has snapped of for the rear sight glass. Currently being held by one bolt which will probaly also snap off. (We are replacing...
  15. What is your control voltage at the contactor...

    What is your control voltage at the contactor when it is not pulling in? I have seen Carrier units locked out through the CLO board and have 16-17 volts at the contactor. When you push it in the...
  16. Replies
    19
    Views
    2,324

    Home depot sells nice garden sprinklers. As a...

    Home depot sells nice garden sprinklers. As a last ditch temp solution it may work until the equipment sizing issues can be addressed. Just dont use it when its cool outside or you will have another...
  17. Replies
    10
    Views
    1,772

    Thanks for the info guys and the manual spinning...

    Thanks for the info guys and the manual spinning wheel. Hopefully will get this thing running tommorrow. Looking at the manual it calls the low side of oil switch connection as the oil charge port....
  18. Replies
    10
    Views
    1,772

    By pumping the oil directly into the suction...

    By pumping the oil directly into the suction service valve it will go directly into the sump where I should be able to see the level in the sight glass correct?
  19. Replies
    10
    Views
    1,772

    I will look tommorrow, maybe I missed it. This...

    I will look tommorrow, maybe I missed it. This job has had numerous problems and I was there late yesterday. What is the oval plate with the spring behind it for?
  20. Replies
    10
    Views
    1,772

    Well I think the oil sight glass can be mounted...

    Well I think the oil sight glass can be mounted in a couple differnt spots on the compressor (judging by the circle plates on the side and rear of compressor housing) but now that you mention it I...
  21. Replies
    10
    Views
    1,772

    Copeland Discus compressor help!

    Was looking at a Copeland Discus compressor (3DA075) that the system lost all its refrigerant and is very low (empty sightglass) on oil. Where is the correct port to pump oil into the compressor. The...
  22. Replies
    6
    Views
    1,675

    Old post brought back, but Yes! I do still have...

    Old post brought back, but Yes! I do still have the ignition transformer for sale. Make an offer.
  23. Replies
    3
    Views
    842

    do a search on here for Nextech ....they are the...

    do a search on here for Nextech ....they are the same company
  24. Well I will be 28 years old in July and been in...

    Well I will be 28 years old in July and been in the field since 18 right out of high school. (hard to believe its been 10 years WOW) I have been a liscensed ham radio operator since I was 13 and love...
  25. Replies
    4
    Views
    775

    heard good things about Boland. I have a buddy...

    heard good things about Boland. I have a buddy who works for Fidelity in Beltsville. He likes it though he said there is the normal politics stuff with most big companies. I work in Baltimore so I...
Results 1 to 25 of 475
Page 1 of 19 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event