Search:

Hello Gents-

I have an Evolution 3 stage 80K BTU gas furnace with the Evolution Controller. My AC unit is a single stage 2.5ton Bryant unit.

On the Evolution controller under Furnace settings...

I was thinking white vinegar rather than bleach. Wha-do-ya think?

Hi- I have a condensate trap coming off the air handler for my AC as well as a condensate drain line coming from my high efficiency furnace. The two drains end up connecting and drain into 3/4" PVC...

I noticed water collecting underneath my Bryant Evolution 3-stage natural gas furnace. Popped her open and noticed that the installers had not tightened up the hose clamp at the exhaust pipe...

Tech was out. My unit is operating normally. He said he called Bryant and their tech. support told him that on cooler days (<63F) there's an imbalance of pressure in the system somehow related to...

Thanks.

One thing I have found is that the line-set is rigidly connected to the outside wall (concrete used to fill the hole) instead of the method shown in Fig. 1 page 1 of the install manual...

Sent the video to my installer last night prior to them coming out today. He said it sounded like the 'valves are shutting'. Not sure what that means though! :confused:

Tech will be out...

I'm working on getting my contractor out but wondering if any of you guys want to take any guesses as to what the sound is:

http://www.youtube.com/watch?v=GuYsDH6QSog

It's at about 8-9 seconds...

I have only heard my newer (2-month old) Bryant 116B do this twice. And it only seems to do it when it is cool outside like I describe below.

Last night it was about 65F outside, the...

My installer told me to use white vinegar, not bleach.

What about one of these for the intake (if not bent over 90-degrees) and/or exhaust?

http://savepipey.net/

~43%

SE Michigan

Thanks!

FWIW:

Air Handler: Bryant CAC/BDP CNPVP3617ACA
Outside Unit: Bryant 116BNA036000

Thanks!

Clocker

Thanks for your feedback.

Would the 350CFM/ton setting be more efficient at cooling that the 325CFM/ton setting for my 3ton unit (assuming the difference in humidity is negligible)?

Howdy guys-
I have an Evolution furnace (355CAV 80K BTU) with Evolution control. My AC unit is just a single stage 3-ton (non-Evolution) Bryant 116B.

I have 4 settings on the stat for airflow...

I ended up mounting my own box on the N side of the house and running a 2-wire from it to the furnace myself. My installers electrician came over this AM and pulled the sensor out of the AC unit and...

Hey guys-

Just wondering...why not have a downward fitting so the exhaust points down similar to the intake? Seems like that would be a good way to prevent crap from getting into the exhaust...

I think my Evolution controller said my static number was 0.42...? Is that the number you're looking for?

The furnace is a 355CAV 80K BTU (95%).

AC is a Bryant 116B 3-ton (up to 16.5 SEER).

I think I'll run my own wires and mount the sensor on the N side of my house. But I'll ask my installer to connect the wire to the control board. I'm nervous about going inside the furnace if I...

The sensor is inside the upper section of the AC cabinet clipped to the vertical wall inside the compartment where the big relay and other connections are made. I agree it can never give an accurate...

Thanks for posting! Wish I knew what to look for. How big are they? Is it located somewhere near where the lines go into the condenser unit on the Evolution units?

Thanks!

Kinda though so. But was also thinking that it probably gets shade inside the air condition unit. However, it probably gets hotter inside that confined area nonetheless. Guess I'll give it a week...

Got the new furnace installed today along with Evolution controller. I am really happy with my selection for installers. They guys were great. Got here about 7:15AM and left about 4:15PM. The job...

My my new Evolution furnace installed was installed today. I don't have an Evolution AC unit so the tech installed a Bryant air temperature sensor inside my 116B Bryant outdoor unit in (the same way...

When did the Evolution controller switch from black/gray to color display?

http://www.bryant.com/products/controls/evolution.shtml