Search:

Type: Posts; User: pare

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: VMA1420 Wc-adjust

    by pare
    Replies
    13
    Views
    407

    I've only done it with an NAE. You add the point...

    I've only done it with an NAE. You add the point as an AO but still map it to the AI address (E.G. AI2), this allows you to send the point a command. I don't know how it is done through a Jace. ...
  2. Thread: VMA1420 Wc-adjust

    by pare
    Replies
    13
    Views
    407

    You may have to play around with the priorities...

    You may have to play around with the priorities to see which one works.
  3. Thread: VMA1420 Wc-adjust

    by pare
    Replies
    13
    Views
    407

    Add the slider adjust point as an analog output...

    Add the slider adjust point as an analog output and command to zero. This should override the point in the vma.
  4. Thread: CO2 Sensors

    by pare
    Replies
    5
    Views
    584

    * Any mA or VDC signal will work.

    * Any mA or VDC signal will work.
  5. Thread: CO2 Sensors

    by pare
    Replies
    5
    Views
    584

    CO2 Sensors

    Hi,

    We have 50+ buildings and are looking at standardizing our brand and type of CO2 sensor. We currently have multiple brands/types (many of which need replacement or calibration). Moving...
  6. Thread: NAE Optimal Start

    by pare
    Replies
    0
    Views
    369

    NAE Optimal Start

    I went through the help file for an explanation of what the Temp Differential paramater does. It seems to have a few purposes but my question is this; If the occupied heating setpoint is 21 deg C...
  7. Thread: DX9100 AO

    by pare
    Replies
    2
    Views
    649

    Beauty. I appreciate the additional information....

    Beauty. I appreciate the additional information. Thanks again!
  8. Thread: DX9100 AO

    by pare
    Replies
    2
    Views
    649

    DX9100 AO

    If "Enable Limits" is TRUE and both the "High Limit %" and "Low Limit %" are set to 100% and "Output Forcing" is TRUE and the "Forcing Level %" is set to 0%, does the AO go to 0% or 100%? Which one...
  9. Thread: NCM Calendar

    by pare
    Replies
    2
    Views
    406

    Good to know. Thanks.

    Good to know. Thanks.
  10. Thread: NCM Calendar

    by pare
    Replies
    2
    Views
    406

    NCM Calendar

    I have an NCM 350 with an OWS running PMI 12.03. The sheduling calendar stops at May 2012. Is there a way to add more years to the calendar or am I $%@# out of luck?
  11. Replies
    10
    Views
    2,720

    Green. I sent you the diagram and figures.

    Green. I sent you the diagram and figures.
  12. Replies
    10
    Views
    2,720

    You need to know total load,btu's,gas press...

    You need to know total load,btu's,gas press delivered,length of run,meter size,etc.call the Gas co.They'll help you out.

    I do know all of this. I just need to know if I use 150 feet as my...
  13. Replies
    10
    Views
    2,720

    I don't know of any 24" rule. Scratch what I...

    I don't know of any 24" rule.

    Scratch what I said about the 24 inch rule. I guess what I mean is if you add an appliance, and this appliance is not added to an existing branch E.g. the piping is...
  14. Replies
    10
    Views
    2,720

    Thanks for your response. I originally wanted to...

    Thanks for your response. I originally wanted to branch off the manifold inside but soon realised (after checking B.149.1) that some piping would be undersized due to the new LMR. Branching right...
  15. Replies
    10
    Views
    2,720

    Gas Pipe Sizing Question

    Adding a Natural Gas fire pit in the backyard. If I connect the piping to the firepit within 24 inches of the regulator will other appliances be affected? E.g. If the current "Longest Measured...
  16. Replies
    3
    Views
    966

    Thanks Dave, I did read the part about the +/-...

    Thanks Dave,

    I did read the part about the +/- 8 K reset but the document wasn't clear on whether or not this was achieved with the 10 VDC signal. If it is, then would I be correct in saying that...
  17. Replies
    3
    Views
    966

    Johnson Controls TC-8803-8041

    I have a building with many of these. These stats have a setpoint reset via a 0 to 10 VDC input on terminals 3 and 4. I would like to know how many degrees the setpoint is reset by based on the 0...
  18. Replies
    3
    Views
    378

    Thanks guys.

    Thanks guys.
  19. Replies
    3
    Views
    378

    Scheduling from an NCM

    If I have Alternate and Holiday days set up in my scheduling calendar, however, I leave the holiday or alternate schedule blank for the object that I am scheduling, when a holiday or alternate day...
  20. Thread: JC BASIC

    by pare
    Replies
    3
    Views
    459

    Thanks. You're right, I just read the Binary...

    Thanks. You're right, I just read the Binary Output Object technical bulletin and it confirmed that this is the case. Maybe I should read more often... :rolleyes:
  21. Thread: JC BASIC

    by pare
    Replies
    3
    Views
    459

    JC BASIC

    I am commanding an output with 2 seperate programs. One commands the output at priority 5 and the other commands the output at priority 6. Obviously, both would be commanding the output, however,...
  22. Replies
    12
    Views
    814

    Sounds like what I need. The NAE is an NAE55. ...

    Sounds like what I need. The NAE is an NAE55.



    Good questions. I think I'm going to let the contractors deal with this one. We havn't payed them yet.

    Just a quick note. We originally...
  23. Replies
    12
    Views
    814

    It says: "Server: 3/11/2009 8:30AM EDT" I...

    It says: "Server: 3/11/2009 8:30AM EDT"

    I tried Archiving and resetting the NAE... time is still off. Figured a download would be just as affective. I have a feeling it's going to have to be...
  24. Replies
    12
    Views
    814

    This is correct, any known solutions? Besides...

    This is correct, any known solutions? Besides ripping out the NAE :)
  25. Replies
    12
    Views
    814

    NAE time discrepancie

    I have a stand alone NAE that was ver 3.1, recently got upgraded to ver 4.1. The dst is enabled. When I browse the NAE focus window it shows the correct local time, when i hover over the site name...
Results 1 to 25 of 48
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event