Search:

Type: Posts; User: Paul Pippin

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    38
    Views
    2,529

    The negative in the room needs to be as close to...

    The negative in the room needs to be as close to 0 as possible if all you want to do is create a slight negative. -.01 to -.02 is the suction or negative static that will create the suction you are...
  2. Replies
    13
    Views
    8,766

    I can't find the recall notices but that is close...

    I can't find the recall notices but that is close to the date range of the valves that gave so much problem. I have seen some of the older heils with the little ports stopped up and not proving the...
  3. Replies
    38
    Views
    2,529

    I think some people in here need to chill out a...

    I think some people in here need to chill out a little I doubt anyone in here has the tendancies to run around killing cats. My daughter has 2 and I take allergy shots to prevent my allergies from...
  4. Replies
    38
    Views
    2,529

    Craterlake, I am not sure if your just wanting...

    Craterlake,
    I am not sure if your just wanting to maintain a negative or if you are wanting to maintain a certain amount of fpm across the room. If you are only wanting to contain everything in that...
  5. Replies
    13
    Views
    8,766

    what are the numbers on the smart valve? there is...

    what are the numbers on the smart valve? there is a number stamped on the side of the valve which indicates the date made. Some of these were recalled several years ago. Does it have an on / off...
  6. Replies
    38
    Views
    2,529

    Cut their tails off this will solve your...

    Cut their tails off this will solve your problems.



    right behind the ears
  7. Replies
    5
    Views
    884

    Overall have not found many things that I don't...

    Overall have not found many things that I don't like about there systems and as stated they are constantly updating the software and products.
  8. Thread: Bobs Tools

    by Paul Pippin
    Replies
    13
    Views
    1,718

    thanks

    thanks
  9. Thread: Bobs Tools

    by Paul Pippin
    Replies
    13
    Views
    1,718

    excuse my ignorance but what is Bobs tools...

    excuse my ignorance but what is Bobs tools software? never heard of it.
  10. Replies
    10
    Views
    599

    Great bunch of people and a good way to network...

    Great bunch of people and a good way to network don't get to as many meetings as I would like to but enjoy each one. Join and participate in RSES.
  11. Replies
    22
    Views
    1,167

    I like the new design and changes after I got...

    I like the new design and changes after I got used to them.
  12. Replies
    30
    Views
    1,604

    I think a national fillet contest would be a good...

    I think a national fillet contest would be a good thing for him. Let the victims family members remove a little skin each day for several weeks months.
  13. Replies
    5
    Views
    920

    would be good if they did but I doubt they will.

    would be good if they did but I doubt they will.
  14. Replies
    24
    Views
    943

    thank him roy our prayers will be with him and...

    thank him roy our prayers will be with him and thank you for raising him to respect and fight for this country
  15. Replies
    35
    Views
    8,324

    It may be the refrigerant pulsating through the...

    It may be the refrigerant pulsating through the lines you may want to check on a muffler in the discharge line of the compressor to help prevent pulsations. Just a thought don't know how the...
  16. Replies
    19
    Views
    2,690

    vaco makes some of them also with the magnet not...

    vaco makes some of them also with the magnet not hardly as pricey as the klein
  17. Replies
    11
    Views
    1,264

    I think installation should be mentioned... if...

    I think installation should be mentioned... if your old one died after 6 years then there is a problem with installation.
  18. Replies
    5
    Views
    920

    Working sounds very familiar I think it is their...

    Working sounds very familiar I think it is their new business policy.
  19. Replies
    21
    Views
    10,793

    Try the hand wipes that you buy I don't remember...

    Try the hand wipes that you buy I don't remember the brand of them but I used one to remove keytite pipe dope from my pants and they worked great. I did this before laundering them I don't know how...
  20. Replies
    12
    Views
    1,271

    I use my axim x51 with the gps attachment nice...

    I use my axim x51 with the gps attachment nice but kind of bulky
  21. Replies
    13
    Views
    3,932

    There are several options available on the...

    There are several options available on the Intellipaks one of which is a GBAS ( Generic building automation system )board. I am not exactly sure that you can overide the economiser with it but it...
  22. Thread: sawzall

    by Paul Pippin
    Replies
    17
    Views
    1,477

    I have the miluakee cordless with the...

    I have the miluakee cordless with the articulating nose nice saw and cuts good until the battery weakens a little. eats power a lot wouldn't recommend it unless you were just cutting little stuff. no...
  23. Replies
    9
    Views
    583

    j3 all I want to know is where is the rainbow at...

    j3 all I want to know is where is the rainbow at nice view
  24. Thread: Hello...

    by Paul Pippin
    Replies
    68
    Views
    3,942

    Bob have a couple of questions. I noticed that...

    Bob have a couple of questions. I noticed that you said they were always looking for technicians. When I was at the school they were trying to hire almost everyone who went through the class. Which...
  25. Thread: Hello...

    by Paul Pippin
    Replies
    68
    Views
    3,942

    Welcome Bob I have been to your school in...

    Welcome Bob I have been to your school in Michigan a few years ago very good classes.
Results 1 to 25 of 288
Page 1 of 12 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event