Search:

Type: Posts; User: geoss54

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds; generated 56 minute(s) ago.

  1. Replies
    2
    Views
    260

    I have the furnace serviced 2X [per year. Last...

    I have the furnace serviced 2X [per year. Last time the tech told me the area where they clean/observe was really clean. He said the filters must really be doing their jobs for it to be so clean.
  2. Replies
    0
    Views
    178

    Just posted in AOC Residential

    Sorry just posted in AOC Residential. I think it was the wrong forum for my dilemma. Sorry
  3. Replies
    2
    Views
    260

    Should I get a Media filter?

    Hi, Wasn't sure what to put in title, but will proceed.
    We have a hi-eff. Carrier gas furnace with a Honeywell F300E 1019 EAC, with pre and post filters. I am very conscious of keeping it clean. At...
  4. Replies
    9
    Views
    740

    reply

    So, I should have at least the left run done with 45degree bends and get rid of the wired flex ducting. The supply can be moved up one joist to make it all hard ducting from beginning to end.
  5. Replies
    9
    Views
    740

    reply

    TLhanks, and one more question- if I were to sell the house would this be something the inspectors would frown upon and list as a no-no.....?
  6. Replies
    9
    Views
    740

    reply

    Thanks.
    I would have to see if crushed. If I stick my hand into the supply from the top it just seems bent. There was no cutting of joist. I guess that would be the one that is losing flow the most....
  7. Replies
    9
    Views
    740

    Thanks, Here are various pics from both the left...

    Thanks,
    Here are various pics from both the left and right side runs. I do have them covered partly with insulation. The 2 90degree bends are noticeable. And I have one shot of the place in the...
  8. Replies
    9
    Views
    740

    how much air is lost

    Have 2 6" runs coming off the main trunk feeding the end room The left on comes off the trunk, goes about 8 ' or so then does a 90degree bend down, then another 90 degree bend across the length of...
  9. Replies
    1
    Views
    764

    Honeywell post filters

    Hi, Just have adopted daughter's 2 cats for a year or less. I have the carrier Infinity system with the Hioneywell E300 EAC filter. I have not used the post filters. My static without them on normal...
  10. Replies
    10
    Views
    951

    reply

    Thanks
    I have 5 supply registers to the main levbel The one to the kitchen is the closest to the plenum and I have it dampered quite a bit because of the strong air flow. The other 4 are equidistant...
  11. Replies
    10
    Views
    951

    reply

    Thanks. I am thinking of asking him to replace the one run because it has 2 90degree bends, and a 45 and the last bit of run(about 1.5') is the aluminum type flexible ducting to fit(it is still...
  12. Replies
    10
    Views
    951

    reply

    so no difference in the flow of air? Air being blown out more forcibly?(dampers are fully open
  13. Replies
    10
    Views
    951

    reply

    Thanks. One thing is for sure is that every joint along the 2 lines were sealed with mastic, even the bends were sealed, take offs that come out of the main trunk-everythong sealed. I was strictly...
  14. Replies
    10
    Views
    951

    replacing ductwork

    My friend who is a contractor put a couple of runs in this weekend for me which had rust inside.
    I also have two runs at the other end of the house feeding an addition(these runns have bends in...
  15. Replies
    4
    Views
    386

    reply, again

    The installer said he would put the damper about 4" down the 6" duct, and when connected to the take-off it would be partially in the take-off, when fully open
  16. Replies
    4
    Views
    386

    reply

    does an open damper noticeably reduce the amount
    of supply air? Thanks
  17. Replies
    4
    Views
    386

    Damper question

    I am having about a 3.5' floor duct from the main trunk line replaced(rust, smelly) I will never touch the damper. Should one be put in?, or leave it without damper. Will the lack of a damper make...
  18. Replies
    3
    Views
    829

    reply

    Thanks for the info, but you have me with the water stops, and the other stuff you mentioned. I do know about braided hoses, only. Thanks.
    George
  19. Replies
    3
    Views
    829

    should I tape the top?

    Should I tape the top of this downpipe for the washing machine and condensate discharge.
    Sorry did not know how to delete the previous post....
  20. Replies
    3
    Views
    1,945

    [QUOTE=geoss54;12049731]Hoi, Including a pic of...

    [QUOTE=geoss54;12049731]Hoi,
    Including a pic of my drain set up for the washing machine. The downpipe has the HVAC condensate draining into it and the washing machine water. The copper pipe empties...
  21. Replies
    3
    Views
    1,945

    [QUOTE=geoss54;12049731]Hoi, Including a pic of...

    [QUOTE=geoss54;12049731]Hoi,
    Including a pic of my drain set up for the washing machine. The downpipe has the HVAC condensate draining into it and the washing machine water. The copper pipe empties...
  22. Replies
    3
    Views
    1,945

    [QUOTE=geoss54;12049731]Hi, Including a pic of...

    [QUOTE=geoss54;12049731]Hi,
    Including a pic of my drain set up for the washing machine. The downpipe has the HVAC condensate draining into it and the washing machine water. The copper pipe empties...
  23. Replies
    3
    Views
    1,945

    do I need a vent for the washing machine?

    Hoi,
    Including a pic of my drain set up for the washing machine. The downpipe has the HVAC condensate draining into it and the washing machine water. The copper pipe empties into the main sewer line...
  24. reply

    Thanks everyone. We'll be thinking of the South the next time you guys shut down because of flurries in the forecast. LOL.
    Thanks, again!
  25. what to do with furnace outdoor intake and exhaust

    Hi,
    Have a hi-eff gas Carrier with the intake and exhaust outside the house. Am preparing for Irene in the Philadelphia area. Should I cover the 2 openings to prevent water entering them???Thanks...
Results 1 to 25 of 378
Page 1 of 16 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event