Search:

Type: Posts; User: ReverseRotation

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    271

    ax programer looking for work

    Hopefully this isnít against site rules. I am looking to do some freelancing so to speak of- during the nights and weekends, with an Ax if a contractor is interested. I have done a ton of work...
  2. Replies
    0
    Views
    260

    Commercial tech Deptfort nj

    Figured i would post on here, looking for someone who, has exp with rtu's 5-50 tons, wshp, towers, boiler, pumps, mini splits, mau, etc. in the NJ/pa location. Competitive pay, 401k, benefits,...
  3. Replies
    5
    Views
    997

    I have had good luck with the following setup, if...

    I have had good luck with the following setup, if it helps
    tr= 2
    intg= 10.0
    dev= 0.10
    dead= .01
    dbdelay= 0
  4. For the conversion error, make certain the...

    For the conversion error, make certain the physical point (ui1) and the software point is configured both as deg c or deg f. Also do the same on the other controller as well. Just an idea.

    As far...
  5. Replies
    8
    Views
    1,171

    It was mentioned that orange and black are...

    It was mentioned that orange and black are actually shorted for low speed, via the ing board. on the wiring diagram it has what appears to be one relay with a com, n.o, and n.c contacts (one coil)....
  6. Replies
    13
    Views
    2,360

    You may want to pickup a service tap, cause the...

    You may want to pickup a service tap, cause the service valves are pointless at this point to recover refrigerant. Even if the refrigerant slowly bleeds threw the restriction i would still tap the...
  7. Replies
    13
    Views
    2,360

    Sounds like a restriction in the condencer or...

    Sounds like a restriction in the condencer or between the compressor and liquid line service port.

    I hope you already checked the liquid line service valve to make certain its open?
    Is there a...
  8. Replies
    15
    Views
    2,791

    from the looks of that its a 3 phase circuit...

    from the looks of that its a 3 phase circuit (breaker 28-30-32 In sharpie) controled by a double pole switch ? guess whatever works.
  9. Replies
    5
    Views
    743

    1. Interlock the chiller to the VFD so that if...

    1. Interlock the chiller to the VFD so that if the VFD loses power or is turned off that the chiller will be disabled.

    Put a current sensor on a leg on one of the legs to the motor. When the...
  10. Replies
    11
    Views
    749

    they say the lonnetwork can handle up to 128...

    they say the lonnetwork can handle up to 128 nodes/controllers (if I remember correctly. however that can be little unrealistic, cause it boils down to, how long your com is, if there is any rf...
  11. Replies
    84
    Views
    5,631

    there are jobs out there however with this...

    there are jobs out there however with this economy there are also a lot of tech's/mechanics laid off and they also want to find work tommorow.As you probably witnessed
    May want to check...
  12. I was curious to know if there is some type of...

    I was curious to know if there is some type of product out on the market to reline a in slab duct work. I am thinking no but yet again I am still new to the hvac industry. The reason behind this...
  13. Replies
    2
    Views
    528

    Hello, all. Does anyone know of any companies in...

    Hello, all. Does anyone know of any companies in the nj/pa area (cherry hill area) or within 40 min drive, that are hiring HVAC tech/install. I am a graduate of pennco tech and have all my epa...
Results 1 to 13 of 26
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event