Search:

This is at FBI agents home , so , I could tell you , but then ..... well.....

I normally see Bryant

why do you insist upon holding your cellular device upside down ?

Im thinking you might not be aware ECM X13 motors have 2 different voltages going to it , therefore you might not have your meter in the right check points

We cannot give you details on wiring ,...

"Mandates" is a cop out

I think the Maytag Man - commercials - triggered something

Maytag used to brag about their machines never breaking down , and the repair man just sat on his ass bored ...

Basically anything built within the last 10 years , they either have engine issues , or trans issues

And when they break down - the repair is so expensive you wonder if its even worth it -...

Money talks I reckon

Im a retired mechanic , and always like Ford

But talking to friends who are still mechanics tell me Ford , Chevy , Dodge , cant build an engine or transmission to last...

Rocky Boots

its upflow , so im sure it lifted the paper off the surface whenever the fan came on

R22 system , Goodman , Up flow furnace , they been there a Long time.

I don't understand how it's still in tact , that's crazy

75 ton coil ..... dam that sounds heavy

I was an Auto Mechanic 20 years .... and was torn on what else I could do .... was getting burn out

So I found a small guy who needed help on the weekends and some nights

Ran around with him...

Yeah thats probly what the guy was thinking

Im trying to imagine if ANY air could pass through the coil ... and Im thinking no , not a drop

Evidently that unit works off a Nitrogen/ Oxygen mix

Corny probly installed it ....

nice work right there

claims he knows HVAC .... pffft .... sure he does

Yeah I wouldnt try diagnosing any further until the power was fixed. That might solve it

I.ve only seen it drop in pressure when another appliance kicks on

Does that have a low pressure switch ? Maybe its shutting it off

Well its a good thing you came along after all of the details were available - to clear that up for us

I think hes talking about using a HP that is sitting in his garage collecting dust .... and its 3 phase

If this is the case ..... I think he can just change the "compressor" to single phase one...

You might ened up taking a wild guess , throw it together and see how she operates

How long is the cap tube now ? like 4 feet ?

Sometimes I fire a unit up , and after 15 minutes the suction...

Only 2 ways that i can think of

THe way you did it

Or , pull a burner , and hold your hose onto an orifice , or try shoving a rubber fitting into the orifice , works just as good

Locked Rotor is 21 and running 19 ? Thats a very small gap

I've never worked on Inverter

Are they DC volts ?

Definitely a Carpenter kind of job

I use tees when there is room

Manitowocs .... I've just been slapping a supco fan cycle onto the high side port. Its rare you need to gauge up , so I figure ... why not

I've always been nervous about those crimp tools ..... afraid Id create a leak when trying to round it back out

10 years ago I was helping a friend of mine diagnose a package unit inside the office of this Exxon Gas Station (his side job)

The unit was bolted to the wall and actually had a huge section of...

they do look pretty ....

Seems aweful silly to have the heat pump running with aux heat strips ..... just set it up as having the furnace run below 36 degrees

yup , and you are testing temperature far away from the evap , so its collected all of the heat it can at that point

Because the pressure you are reading is a conglomerate of the lineset (and its long legnth) plus the pressure differences going on inside the evaporator (during all of its chemical reactions taking...

hmm...

yeah i checked amps when the mix was 40 degrees , so im not sure the amps at 5 degrees

well , it has a contactor for the compressor , so it only runs the shaft that turns the mixture which pulld 3.5 amps

120v unit

Its crazy how such little amps causes a fire , but it happens all...

Before replacing ....you can see the top one caught fire

Who is familiar with this famous problem of switches catching fire?

Have you ever found a way to prevent it ?

The rubber boots were actually in nice shape , so I cannot blame water getting...

https://www.youtube.com/watch?v=KlkuNfDz5qY

Toby verses drunk guy in crowd

you've been cheating on us for over 15 years ???? with who ??

I've never been successsful to find a leak on 290 system yet ... I suck

they self clean for about 2 years , then eventually the plastic bristles wear down to the point of not hitting the metal mesh anymore

2nd picture is the self cleaning brush , sitting on the bottom

so it never dropped in temp after couple hours , so went back , added a line tap , and added 1 oz 290 (total charge is 3.5)

Temperature began to drop , So i left for now

Need to return one...

So I came across this today , 4 year old unit , holding 54 degrees when I arrived.

R290

Removed the stupid piece of shit self cleaning assembly , threw into the trash

Found the COIL behind...

So I had time to babysit it

Dropped a few sheets , made sure the pusher was working , yup its working , then all the sudden the 4th sheet stopped halfway out of the grid ... and held the door...

I replaced the board, watched it drop two batches, and went home thinking that HAD to be it.

I think it made ice for one day and then was back to the same BS

But ....he was telling me the F was...

?

They broke the knob off

Ok so .... I haven't seen the issue in person , I've been going off what the managers telling me.

The dam thing works fine while I'm there

When they came in this morning the F was blinking
...