Search:

you do need water treatment both closed and open loops spent time rebuilding and maint. in phx az .now years ago we used nitrite but found out that it could form bacteria so we switched to mulibdate....

THE ONLY HOSHI IVE EVER SEEN SLUSHI IS DCM WHEN THEY 1ST CAME OUT HAD TO PUT TIMER ON THEM . ,

This is the Ask Our Pro's forum. In order to post a response here, you must have verified qualifications and have been approved by the AOP Committee. You may ask a question by starting a new thread....

DO YOU SEE SOME OF THE ORFICE FROST I HAD TO REPLACE HEADER KIT .

YOU HAVE RELIEF VALVES ON YOUR WATER OR GLYCALL CONDENSER THAT COULD RELEASE IF YOU DO THAT; I WOULD HOOK UP FLOW CONTROLE THAT IF I LOOSE FLOW MY BACK UP PUMP WOULD COME ON ,ALSO I WOULD TEST IT 4...

AFTER YOU PUT NEW GEAR BOX IN MAKE SHURE YOU BALANCE IT ALSO ALINE SHAFT CORECTLY OR YOU WILL BE REALING ON WOBLE SWITCH TO SAVE IT HAVE DUNN A FEW.FUN STUF GET A HOLD OF MARLY OR REP FOR SPECKS ON...

IF YOU HAVE MOISTURE IT WILL FREEZ AND ICE TAKE TORCH HEAT UP IF IT GOES AWAY YOU HAVE MOISTER IT WILL BREAK LOOS LIKE ICE PLUGG ;

GET AHOLD OF WATER TREATMENT PEOPLE THERE WATER TREATMENT CONTROLLER MIGHT BE OVER FEEDING CHEMICALL

might wont to check on new evap .easer saID THEN DUNN

have exp on cooler cond water temp it started to surge did not like it went back to flat plate .

:cheers:please explain further bind llids ;

not pretty broke one hade to have wellded also had a machine were got lucky grinded and had to drill tap install new bolts check your tubes really good when you get head off .time to brush . or rod...

lets have fun clean and rod condensers edycurent and inspect tubes cooling tower maint mudy but good money in winter 'along with strainers and controlls ; cooliing tower s some need oil change in...

depending what cooler you have j1 j3 1130 # alot of times if your machine is down 4hr or longer you can look in sight glass will be 1/2 +- 1/4 all pumps must be off. if you give model number i might...

i had transducer on start up do the same thing it was bad right on start up fun

keep water moving both chilled and cooling tower or should say condenser water or you could pop a tube had to retube from finding with edycurent..

RUNDAWS IVE WORKED WITH SO MANY PEOPLE THEY SAY BETTER LUCK THAN SKILL .I LIKE ,INSTEAD OF LEARNING TRICKS OF THE TRADE LEARN THE TRADE SO TRUE ...

R.S.E.S HAD A NICE TRAINING 'HIGH VOLTAGE WERE THYE ACTUALY USED LIVE VOLAGE AND CARBON ARCH FRIED HOT DOGS AND MADE FIREWORKS DISCUSED HOT STICKS AND FLAME SUITES LOCK OUT TAG OUTS 4160 DOWN TO 120...

if you charge to full sight glass you take good chance on a overcharge if you have a txv and the box is warm . i like sight glasses use full,

3 phase moter will have resistance the same on all 3 legs .If not moter bad ,which i worked on a older trane which was a 208 230 volt 3 phase which hinding in the corner was a step up transfprmer 460...

:angel:

becarefull of your ph is to low it will eat through copper tubes ,on those recold .or old dunbush .evap . condesers 'they do make a copper inhibiter 'most of the time with sileca scale being glass...

i have used many was to find water leak blue or green die altra sound turned off the sprinklers for a few days in arizona found the nice green spot .backflow preventor on closed loop every time...

had this same thing happen on 2 york millinium one 450 ather 600 one brand new out of box bad the ather had a loose wire some time would ground causing bad reading took me awhile to find it but the...

i have got my oven gas valves from haritage food . if you need a 1800 3 let me know .they have got a lot of even steam kettle parts;refer parts .

thank you invertor was speeding up to compensate for refrigerant waighed out charge was short waighed back in .got up and running ,went back to leack search found leak in evaperator ,its on the way...

wow suction psi starts at 70 pounds than goes to140 after it ramps up supper heat 20 deg .head psi stays at 290 psi subcool 5 .is clear as mud iam old school like to abrevate spelling allways...

hello skrewdriver spent 30 years in az still hold my phx lic there know in oh ,i hit those coils evap coil cleaner few cans also spray water bottles in those tuff location hey tailler freezer sales...

used 409a ranco a12 700 worked out good

have a mitsubishi muya24na that when it ramps it at 70# gradualy goes to 140 sh 20 hp allway stays at 290 sc 5 amps on start up 6.7 goes as high as 7.5 out side temp 75 indoor 80 .when i first got...

put unit back to gether and put in vac weigh in charge and take amps if it 3ph switch two wire ,if it is a scrolll comp you will have to make sure you do not leave like that . if it is stuck it...

had to retro mini new bin control from mechanical to thermostatic ,dont forget the bin braket.the extension.

got to to love it , midnight call

looking at manuel .place jumper t1 t2 2 contiuous seconds .allowing unit to energize ,the unit can now be scrolled through modes.when you remove jumper it will stay in that mode 1hr . if you need...

i have a infacom it has been the best one .had it 5 y and it still find lots of leaks ,changed diode once .pin holes that brands could not find

FIND OUT WHAT TOTAIL DUCT STATIC IS DIFERANT PART OF THE SYSTEM. FIND OUT WHAT YOUR SC SHOULD BE 20 SOUND HIGH GET THAT AIR FLOW TD 30 HIGH AFTER AIR FLOW THAN YOU MIGHT FIND POSIBLY OVER CHARGE...

I WOULD WONDER HOW MUCH OIL GOT HEATED .AND REMEMBER THERE A REASON WHY DISCHARGE TEMP IS NOT TO EXCEED 225 ;YOUR TORCH IS WHAT TEMP ,

USE POWER EXHAUST AND C02 CENSOR OR FIGURE WHAT YOUR CODE WONT S THEN FIGURE AIR CHANGED PER HR ,

is this a fluid cooler with boiler (COOLING TOWER) if so bring water temp to at least 55 to 65 . this will bring up psi also does this make up air .need a little more info so i can help .Is this open...

i repaired used 409a did change captube and also installed dryer worked out good.:.02:

wondering why not use mo 99 .in place of r22.you dont have to change oil .

a few words describe this job gagageter done .

hellow to a fellow az i lived there for 25 years were i worked and still hold license for city of phx iam curently in oh .

make shure that there is no air leaking into freezer from outside sources ,around linesets.

that was going tobe my next question how too copy and past

thank you i have a great sence of humor ,got to have one in this field . should see how i write after a 18 hr day ,better service through knowledge

take temp of top of comp head with infered gun temp on part of shows hoter in areas or hole head to hot .sounds like valves and valve plate ,

with out seeing belt and location . i had a machine shop with extream oil in the air and the oil effected the belts so bad went to a belt that lasted a few months longer .

sometimes when its 455pm and you need a question they all *******

HELLOW BROTHRER RSES MEMBER I HAVE TRIED TO SCAN MY STUF OVER BUT IT DOES NOT GO THROUGH HAVE TRIED SEVERAIL TIMES ,I AM A RSES MEMBER AND STILL HOLD CITY OFF PHX MECH AND GAS LIC AND ATHERS .IF YOU...