Search:

Yes i do have communication issues, and as of yet, they havent been resolved. Thats a decision thats above my pay grade. I hope that i didnt come across as rude the last time we spoke.
And to be...

Yes I believe I do have SCT, but im not sure about the NAE images.

In regard to the default password, is metasyssysagent used as the username?

Ok how do i NUT the NAE?

I need a default password, or a collection of passwords to try, im using "metasyssysagent" as a the username for an NAE that somehow the password was changed, and now I cant get in. I can only guess...

Bacman...Call someone that knows what they are doing? Thats what I thought I was doing.

JCI man...Although I appreciate all your help and advice, not knowing what the ramifications would be, im a...

What other info do you need?

Ok, here we go.....
The version is: 6.5.0.5500
NETWORK:
NAE3
LAN
DHCP ENABLE: False
IP ADDRESS: same as listed on NAE3
IP MASK: same as listed on ADS for SUBNET
IP ROUTER ADDRESS: same as...

Ok

Great, i will get that to you as soon as i can. Its the latest version, i believe its version 6. And it seem to work fine for about a month or so.

I could write it all out as it appears on the screen

Time zones match. And im sorry, but for some reason im not able to do a screen shot.

Im sorry I mistyped, the "IP Router Address" is not the NAE IP, it is the router IP address.

Ok, im looking at just one NAE at this point to make sure that all my ducks are in a row, or what I need to correct before moving on to any others. In this particular NAE, in the "Network" tab, under...

"Obtain an IP address automatically" and "Obtain DNS server address automatically" are both selected.

I can ping individual NAE's and the ADS.

I should clarify that i have never had any training on Metasys, or any other BAS system. So forgive my ignorance when i ask, how do i ping each NAE from the ADS, and how do i confirm wether its DHCP...

We just had an upgrade to the latest software version, a few months back. The issue developed a few weeks after the upgrade. Im not sure if the ADS is online to the NAE's, but as i said, i can access...

:gah:I can log into my system ADS, and we have 6 NAE's, and all 6 come up with red X's, but if I put in the IP address of an individual NAE within the system, into the launcher, im able to access it....

Very cool!!

Thanks for all the help, with all this information, I believe that I will be able to get it resolved. It appears that from all that ive read, there is an internal board fault on the new boards....

Im looking for the service manual for this oven since I dont have an access code to Blodgett tech support.
The problem that i'm having with two of these ovens is that one works when it wants to, and...

Its been a long time since ive done domestic refers, but if my memory serves me correctly, suction should be low, around 1-2#, high side around 120, and charge by weight, as liquid, through the high...

I looked up the documentation and it says its a 1k.

For testing, can i jumper in a 1k resistor?

As far as i know, its the original sensor.

I was in contact with the manufacturer this morning and given that the outside temp was approx, they told me that it was close, its a 10k sensor.

So terminal #1 of the analog inputs is set for temp.

As it sits right now, SW1: 1-3 on, 4 off, 5-6 on. SW2: 1-3 off, 4 on, 5-6 off.

And which terminal should the oat sensor be connected to?

And ive never programmed or reprogrammed a controller, but ive always wanted to.

Not sure which one was the correct one since the wire that that was labeled for the oat was cut. I did connect a new sensor directly to the board, but no change.

I have an OAT sensor that reads "??? 250*f" on the front end, the sensor and the wiring ohm out ok, I got 17 w/ an OAT of about 56*. Does it matter what analog input terminals I use for the OAT? Im...

This slicer no longer works in auto mode. I was wondering what I need to look for on this, is it merely just a switch? I had this apart about 3 weeks ago to replace the on/off switch and I really...

I did trace the wires and the donuts are connected to the controller. Thanks

Ok, having mainly a residential background, not having to have dealt with this before, I need some advice and/or guidance on how to correct an issue with a building's CT that shows that its offline...

Ive so far found that the cooling fans were CAKED with grease and dust, im going to clean them first. And follow up with all your suggestions. Thanks!

After replacing every component in the ignition system, it lights, but goes out immediately! I would say flame sensor, but that has been replaced as well!!

M: SSB5G S:J77748B-1-1
This dang steamer has been a bur under my saddle for the past year, luckily their are three others that they can use. I have gone thru this unit with a fine tooth comb,...

That's another thing...I have never reallyunderstood sh/sc...can someone splain it in english?

Ok yeah Im not that good at reading my gauges, I admit that, but here goes. R22, 91*ambient, suction 75#, discharge 300#, low on refrigerant? Im only getting about 60* DA temp. Room temp is about 76,...

Im desperately looking for an actual service manual for an SSB5G/J777-48-B-1-1, not the operator manual. Anyone out there have a link to get one or have one that can be emailed to me? Thanks in...

Ill check into that.

The 1st one had a blown out relay on the fan timer, but when I replaced it and the motor was finally getting power, it sounded bad. It took off slow, and ran for a while, unitl tstat was satisfied...

yes 24v to the module

S/N 092107RI0492-Ive had numerous calls on this unit, but I cant ever find a problem with it, yes the dreaded intermittent problem. Although the last time that I was there I set it to 350F, and...

pressure switch is closing

On the first unit, open limit @ hx, I jumpered it out, it lit off, no power to motor on com and high. So I guess I need a board for that one.
And on the 2nd unit, indoor blower operates, combustion...

1st one PGME60H150C/G030612118..thermostat blank, all that's running is the combustion fan motor, no call for heat, got 24v into the control board, but nothing on any of the lv terminals on the...

I get a call that its not heating. It has a tag on the back stating "Wired for 208 Volts", but no where am I getting 208V only 120v. I called CresCor tech support since I didnt have any tech...

Model #: DFG-100-XCEL-DOUBLE. I was wondering if somehow this oven is calibrated differently than others, and if so, what is the correct procedure. I have calibrated a variety of ovens over the...