Search:

Type: Posts; User: Gorgoth

Search: Search took 0.00 seconds.

  1. Thread: Todays rescue

    by Gorgoth
    Replies
    12
    Views
    882

    Why the hard-start?

    Why the hard-start?
  2. Thread: Advice

    by Gorgoth
    Replies
    14
    Views
    1,038

    All I can say from a Apprentice point of view. If...

    All I can say from a Apprentice point of view. If you don't make this trade your life right from the start and you dont show a ton of intrest your journemen will know and not spend much time with you...
  3. Replies
    8
    Views
    751

    Thanks for all the tips :) And thank you for the...

    Thanks for all the tips :) And thank you for the complement. I really do love this trade I look forward to work everyday. Just want to avoid any stupid mistakes and learn from my others.
  4. Replies
    8
    Views
    751

    First compressor and drier change

    Well on I got my first compressor change out and drier to do. Its on a wall mounted sun unit. I have all ways just tagged along but never on my own.

    Just want to make sure I got the steps.
    ...
  5. Replies
    3
    Views
    396

    Well I checked on that and its currently within...

    Well I checked on that and its currently within code except for double wall flue.
  6. Replies
    3
    Views
    396

    Installed a water Heater

    Well had a call the other day and was to install a water heater. The flue set up was going at a 45 Degree to the flue for the furnace and they joined up. So I went and just attached the flue to where...
  7. Replies
    7
    Views
    1,621

    Checking Voltage

    Dont have a picture but I was on a service call and the facility manager was on the roof with me and she told me that she wants to check the line side voltage on all the disconnects. ( I don't know...
  8. Replies
    7
    Views
    619

    Preventive Maintence

    What do you look for when your starting a PM?
    Also what do you try to bring with you?

    No piece of equipment in specific.
  9. Replies
    3
    Views
    722

    I am one.. lol None of the parts houses here will...

    I am one.. lol None of the parts houses here will get back to me and I ask some of the other guys I work with. They told me that I have to look online then send it to the shop to order.. :(
  10. Replies
    3
    Views
    722

    Hard time finding parts for a intertherm

    Anyone know where I could look up parts for this? Need to find a reversing valve relay and a control board.
  11. Replies
    9
    Views
    588

    1 1/8

    1 1/8
  12. Replies
    2
    Views
    346

    I had the same issue with a Mr.Slim a few months...

    I had the same issue with a Mr.Slim a few months ago. I turned off both disconnects for the unit. Turned the one on the roof on gave it 3 mins then the other they both began to talk again and my stat...
  13. Replies
    1
    Views
    261

    Hard time finding parts

    Anyone know where I could find a parts break down for a Intertherm heat pump?

    I tired there web site but it doesn't tell you ****.

    PWY03KLRAB05

    Any info would help.

    Thanks
  14. Replies
    4
    Views
    886

    Siemens

    Eh good luck with that Siemens.... I have nothing but problems with all the Siemens controls and Square D drives. Maybe its just Siemens here in California but its sad. If you figure it let me know...
  15. Replies
    13
    Views
    1,705

    Also I have seen some motors have sealed bearings...

    Also I have seen some motors have sealed bearings that don't need grease... And people load the **** out of them with grease thinking it will help and turns out it needs new bearings.
  16. Replies
    4
    Views
    886

    Well I'm not sure if this is correct. But I was...

    Well I'm not sure if this is correct. But I was working on one today and electricians connected S1, S2, S3 lines into a disconnect next to the fan coil with a disconnected going to the unit. Then up...
Results 1 to 16 of 16
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event