Search:

Type: Posts; User: -MAKE-

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    1,252

    Apparently I have not been active enough because...

    Apparently I have not been active enough because banner tells me to post.

    Where did that come from? Correct me if I'm wrong but as I recall EN 378 doesn't say that. Every COMPANY has to have at...
  2. Replies
    28
    Views
    1,692

    I have been doing electrical for over 15 years....

    I have been doing electrical for over 15 years. Automation, machines, commercial, household, you name it. There is so much to learn and to keep up with. Codes and overall technical development. Few...
  3. Replies
    23
    Views
    3,754

    That's right. Voltage drop depends on the diode...

    That's right. Voltage drop depends on the diode you use but it usually falls between 0,4-0,8 or something like that.
  4. Replies
    23
    Views
    3,754

    Another trick is to put a normal diode in series...

    Another trick is to put a normal diode in series with the 4-20mA signal. Then you can check the current in milliamp range by simply measuring across the diode. The meters resistance is so small that...
  5. Thread: fluke 179

    by -MAKE-
    Replies
    4
    Views
    760

    Yeah, that's right. And rain sucks. Here's a...

    Yeah, that's right. And rain sucks.

    Here's a little tip about checking the fuses. Put meter in the ohm or diode range, and measure with red or volt/ohm lead against the amp terminal. It will show...
  6. Thread: fluke 179

    by -MAKE-
    Replies
    4
    Views
    760

    I'm wondering, what are you asking?

    I'm wondering, what are you asking?
  7. Thread: CO2 article

    by -MAKE-
    Replies
    17
    Views
    1,788

    We had the first co2 supermarket in 2007. It was...

    We had the first co2 supermarket in 2007. It was cascade.
    Now they are building first full co2 dx supermarket. It's supposed to be 15-20% more efficient than conventional system.

    Also we have...
  8. Replies
    44
    Views
    3,229

    I have Fluke Ti-20, Scopemeter123, 335, 52II,...

    I have Fluke Ti-20, Scopemeter123, 335, 52II, 971, 322 and 62 at least, maybe there's more. And like them. Most of them get tossed around in my van and they seem not to care about it. Oldest one I...
  9. Replies
    9
    Views
    764

    I have a small lathe and a small mill. Don't use...

    I have a small lathe and a small mill. Don't use them everyday but when needed, "priceless". Lathe is chinese noname but it does it's job. I can get less than 0,1 mm accuracy easily. Even done some...
  10. Why don't you just recover the refrigerant and...

    Why don't you just recover the refrigerant and put it back when you're done?
  11. Replies
    10
    Views
    506

    What can I say but we know our stuff

    http://abcnews.go.com/Blotter/car-company-us-loan-builds-cars-finland/story?id=14770875#.TqHVH_t3vRo.twitter
  12. Thread: Vacuum Troubles

    by -MAKE-
    Replies
    90
    Views
    4,544

    OK, where can I get one? I have to see for...

    OK, where can I get one?
    I have to see for myself.
    None of the links from accutools for Europe showed one. I did not even look at Romanian and Italian sites because.... Well... Not gonna order from...
  13. Thread: Vacuum Troubles

    by -MAKE-
    Replies
    90
    Views
    4,544

    Would you explain what POE has to do with this?

    Would you explain what POE has to do with this?
  14. Replies
    9
    Views
    536

    Thermal imager shows a distinct pattern if there...

    Thermal imager shows a distinct pattern if there is a air leak compared to thermal conduction. This is at least here where the norm is having the building in a slight negative pressure. You guys that...
  15. Replies
    10
    Views
    1,334

    DC jack of my Fluke thermal imager busted and the...

    DC jack of my Fluke thermal imager busted and the thing travelled to Washington for repair. They upgraded the jack AND calibrated the imager. Cost me nothing.

    Now keep in mind where I'm...
  16. Replies
    46
    Views
    3,708

    I use torque wrenches all the time on flare...

    I use torque wrenches all the time on flare fittings and machine repairs.
    If fact in Europe there is a refrigeration standard that says what torque to use by the diameter of flare. Must be the...
  17. Replies
    7
    Views
    549

    Have your tech read the installation manual....

    Have your tech read the installation manual. There he will find the limits of installation lenght and height difference between units. Also what has to be done to extend those limits to maximum.
  18. Replies
    23
    Views
    1,114

    Can I have my * now:angel:

    Can I have my * now:angel:
  19. Replies
    23
    Views
    1,114

    And in the mean time fighting russians we just...

    And in the mean time fighting russians we just figured it out that 3phase is the way to go:grin2:
  20. Replies
    23
    Views
    1,114

    Keep in mind that we were the ones who kicked the...

    Keep in mind that we were the ones who kicked the soviet outta here:cheers:
  21. Replies
    23
    Views
    1,114

    Yes, they realized that 3 phase is is better.

    Yes, they realized that 3 phase is is better.
  22. Replies
    23
    Views
    1,114

    Come visit me. All 3 phases except few houses...

    Come visit me. All 3 phases except few houses from the 30's to 40's:grin2:
  23. Replies
    9
    Views
    1,407

    Noup. I would get slapped by moderators.

    Noup. I would get slapped by moderators.
  24. Replies
    9
    Views
    1,407

    Do you think multiple posting will help?

    Do you think multiple posting will help?
  25. Thread: TXV hot swap

    by -MAKE-
    Replies
    49
    Views
    4,570

    So what's the deal? Anyone? Around here you...

    So what's the deal? Anyone?
    Around here you can't vent HFC:s but I'm curious what the EPA says.
    In my world ODP is as much of a factor as GWP. Can't vent and need license.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event