Search:

Type: Posts; User: dodger454

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    452

    If the NAE's are Rev 5.2 or higher go to JCI...

    If the NAE's are Rev 5.2 or higher go to JCI website and download the launcher program.It's free and the java is built in to the program.
  2. Replies
    7
    Views
    426

    Something doesn't sound right.If JCI installed...

    Something doesn't sound right.If JCI installed the job with a Metasys ADS/ADX server then they should have left the software,and the customer could have added/deleted software. Coming back after 5...
  3. Replies
    15
    Views
    1,497

    What Revision of Metasys are you dealing with?

    What Revision of Metasys are you dealing with?
  4. JCI Guys need help with Vtools and Windows 7

    Got my new JCI win 7 pc and can't get V-tools SCT to work can anyone help??
  5. American Standard Heat Pump wiring diagram HELP!

    I don't do residential work but a friend of mine bought a used AM STD heatpump.He asked me to do the control wiring hookup.There are no wiring diagrams that aren't badly faded and this unit uses wire...
  6. Replies
    10
    Views
    974

    See if you can move over to the service side of...

    See if you can move over to the service side of JCI.But if you looking to be around women good luck,you will spend most of your time behind the scenes with the building maintenance people.On the...
  7. Steps to load UNT configuration into VAV...

    Steps to load UNT configuration into VAV controller.
    1. the UNT xxx.cfg file in Notepad. (xxx = filename)
    2. Change the following:
    a. Device Group: UNT to VAV
    b. Device Name: UNTxxx-x to VAVxxx-x...
  8. Haven't done this in a while,I think You need to...

    Haven't done this in a while,I think You need to save file as a UNT.Then change the .PRN file back to VAV.It's a pain.I have a file somewhere on the exact steps.Let you know when I find it.
    LU 449
  9. Replies
    9
    Views
    615

    There has been rumor of a N2 FEC for over a year...

    There has been rumor of a N2 FEC for over a year but nothing yet,and rumors of the VMA 1600 being configured for N2,again nothing yet.One thing to keep in mind if your facility upgrades to Windows 7 ...
  10. Replies
    8
    Views
    555

    Check the firmware code, HVAC...

    Check the firmware code, HVAC Pro-Action-controller information.If it's a 8.08B it should be C05,If it's C02 or lower download the C05 code.This must be done thru the N2 bus.Also make sure you upload...
  11. Replies
    13
    Views
    1,422

    2 ways to reset PID,upload controller and then...

    2 ways to reset PID,upload controller and then download it.That resets the PID,or change the adaptive tuning to manual then change it back to adaptive tuning.CCT 5.0 and up have a network input reset...
  12. Replies
    5
    Views
    954

    WARNING !! This setting should only be entered...

    WARNING !!
    This setting should only be entered into the gx9100.ini file if you intend using
    the password feature. If a DX controller has been password protected and the
    password has been mislaid...
  13. Replies
    0
    Views
    488

    For Sale JCI NCM 300 and 350

    I believe they were reconditioned less than 5 yrs ago. Make offer
  14. Replies
    5
    Views
    954

    he ability to set a password in the DX via the...

    he ability to set a password in the DX via the GX9100 is dependent on
    having the following line in the [Settings] section of the gx9100.ini file:
    PasswordEnable=Yes
  15. The NCE is the eventual replacement for the...

    The NCE is the eventual replacement for the DX-9100
  16. Troubleshooting help with Siebe MN-ASDI integrator

    Working on a system that uses 2 ASDI integrators that feed into a TAC UNC-520 integrator that are IP bacnet to Metasys.One works the other one does not.The bus voltages are the same and all devices...
  17. Replies
    9
    Views
    1,362

    There's some great customer service.Mr Customer...

    There's some great customer service.Mr Customer you need to replace this contoller because I have no idea how to upgrade it.
  18. Replies
    9
    Views
    1,362

    use the "port dump" to get your IP address,use a...

    use the "port dump" to get your IP address,use a switch not a crossover,and read all instructions in the LIT then try again.Also if you are trying to upgrade a NAE 55 make sure it is a NAE 55xx-1, a...
  19. Metasys 5.0 is rumored to be compatible with...

    Metasys 5.0 is rumored to be compatible with Windows 7
  20. Thread: WGX9100

    by dodger454
    Replies
    16
    Views
    2,213

    blackbelt unless you are a JCI employee I don't...

    blackbelt unless you are a JCI employee I don't think you can.It has to be dowloaded from the JCI portal and each JCI Branch must license it.
  21. Thread: WGX9100

    by dodger454
    Replies
    16
    Views
    2,213

    GX-9100 is in M-Tools WMX-9100 is not

    GX-9100 is in M-Tools WMX-9100 is not
  22. Thread: WGX9100

    by dodger454
    Replies
    16
    Views
    2,213

    I'm pretty sure theWGX is a propriatory JCI...

    I'm pretty sure theWGX is a propriatory JCI program.It comes from JCI Italy.
  23. Replies
    12
    Views
    986

    Save the file as a UNT then edit the config file...

    Save the file as a UNT then edit the config file using note pad and change the UNT to a VAV and save file using notepad.Download the controller with the edited file and then upload and commission.Not...
  24. Replies
    53
    Views
    4,069

    I agree that no matter which side Control techs...

    I agree that no matter which side Control techs come from there are scrubs on both sides.I am bias to the mechanical side because a good HVAC mechanic knows why things operate they way they do...
  25. Replies
    53
    Views
    4,069

    Controls Guys

    Some of the larger controls companys are finding its easier to teach us "freon jocks" the digital controls end of the business,than to teach the computer jocks HVAC.We actually know why things do...
Results 1 to 25 of 26
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event