Search:

Type: Posts; User: hvactech1jm

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    805

    flame failure ,fan failure ,control problems they...

    flame failure ,fan failure ,control problems they were all put in last winter/spring.
  2. Replies
    6
    Views
    805

    Just a big fan and a powerflame burner huh must...

    Just a big fan and a powerflame burner huh must be different than the one were are workign on.
  3. Replies
    6
    Views
    805

    gas with oil back up that is never used. its a...

    gas with oil back up that is never used. its a different problem everytime we turn around.i have the start up book but that only get you so far.
  4. Replies
    6
    Views
    805

    Johnson air roatation system problems

    i recently started a new job doing commercial hvac and the plant i work at had about 9 Johnson air roatation systems put in and been nothing but problems. i was wondering if someone could lead me to...
  5. Replies
    10
    Views
    590

    its better to keep moveing parts moveing so yea...

    its better to keep moveing parts moveing so yea let it like it is
  6. just wanted to add something else programable...

    just wanted to add something else programable stats could help a little bit.
  7. very possible the price is whats killing people....

    very possible the price is whats killing people. lots of people think they are useing more fule but most of the time they are not its the prices goin up and down that gets you.
  8. how far is the water heater from the washer

    how far is the water heater from the washer
  9. Replies
    31
    Views
    1,363

    you got buddy thats what i did today the...

    you got buddy thats what i did today the coustmers were there so i went out and set in my van and went through the hole thing again till i had it right.see the problem is the company i work for is so...
  10. Replies
    31
    Views
    1,363

    i got it figured out today i went back through...

    i got it figured out today i went back through and reset all the settings i must of had one of them wrong because it worked fine after i did that. thanks for all the help guys
  11. Replies
    31
    Views
    1,363

    thanks for all the info when i work on it...

    thanks for all the info when i work on it tomarrow i will let you no what happens.
  12. Replies
    32
    Views
    3,506

    i havent had much luck with either of them. just...

    i havent had much luck with either of them. just my opinion you no there like a**holes everyone has one.
  13. Replies
    31
    Views
    1,363

    yea i no its a pain i hvae s1 an s2 hooked up and...

    yea i no its a pain i hvae s1 an s2 hooked up and i followed the digram. evrything works fine except when the gas furncae kicks in to help the hp. the gas furncae runs fine in em heat and the hp...
  14. Replies
    31
    Views
    1,363

    ok

    ok
  15. Replies
    31
    Views
    1,363

    iam the contractor i never used this stat and...

    iam the contractor i never used this stat and thats why im asking.
  16. Replies
    32
    Views
    3,506

    Weil McLain Boilers are just as bad as Burnjunk...

    Weil McLain Boilers are just as bad as Burnjunk boilersevery dam one of them crack. Bryant makes a good cast iron boiler and new yorker makes a good steel boiler.
  17. Replies
    31
    Views
    1,363

    gas furn heat pump combo problems

    i have a tempstar 90+ gas furnace and a tempstar heat pump and i used a honeywell pro vision 8000 stat with outdoor sensor. when the heat pump cant keep up the gas furncae kicks in but the heat pump...
  18. Replies
    7
    Views
    539

    blower houseing bearings

    i have a patriot oil hot air furnace that has bad bearings in the blower. how hard is it to replace the bearings in the blower houseing this is one thing i havent done yet so im not sure what im...
  19. very common system where i live in central PA....

    very common system where i live in central PA. the company i work for has put tons of them in. it should be pretty good system if it was installed properly.
  20. Replies
    44
    Views
    14,729

    we silcone all joints in duct to keep it from...

    we silcone all joints in duct to keep it from comeing apart plus staple it and tape it
  21. Replies
    5
    Views
    530

    i would say it has to be a delayed ignition i...

    i would say it has to be a delayed ignition i dont no what else would cause this.
  22. Replies
    17
    Views
    1,113

    well if you have a leak in a 410a system they...

    well if you have a leak in a 410a system they should have pumped all the freon out of and put new in, because 410 Fractionates when there is a leak in the system. If they were certified in 410 they...
  23. Replies
    17
    Views
    1,322

    sounds to me like someone is feeding you a line...

    sounds to me like someone is feeding you a line of crap, you should have all your supplies open. i would say someone may have undersized your system or your duct work and this is why they are tell...
  24. should be one under it all new transformers come...

    should be one under it all new transformers come with one, it shiould have one but useally it doesnt make a huge diff.
  25. Replies
    4
    Views
    839

    got it figured out guys its ok i got my meter out...

    got it figured out guys its ok i got my meter out an tested how the old an new one worked then i wired it up and it works
Results 1 to 25 of 70
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event