Search:

Type: Posts; User: knave

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    473
    Views
    39,096

    You need ak900 so bad dude.... I can't imagine...

    You need ak900 so bad dude.... I can't imagine toggling all the time!




    Kidding
  2. Replies
    58
    Views
    4,004

    Thanks Sent from my iPad using Tapatalk

    Thanks


    Sent from my iPad using Tapatalk
  3. Replies
    58
    Views
    4,004

    Brent, Thanks for the great review. i've used...

    Brent, Thanks for the great review. i've used mine for 2 years or so, and my experience has been very good as well.
    BUT my gauge is slightly loose from the nut on the bottom, so far I haven't...
  4. Replies
    204
    Views
    29,529

    i have the h602 as well, when it is on, you can...

    i have the h602 as well, when it is on, you can see no darkness. The wide beam angle makes the whole room light up... the "w" version has a warmer tint which would be a good thing, mine is more...
  5. Replies
    84
    Views
    3,913

    Good story, well told!glad it turned out ok

    Good story, well told!glad it turned out ok
  6. Replies
    84
    Views
    3,913

    Got My n2 tank to sweat up when pressure checking...

    Got My n2 tank to sweat up when pressure checking a large twinned Vrf system.

    But yeah you would have a little bit too much flow for proper brazing at that point!
  7. Replies
    84
    Views
    3,913

    How do you go about refilling the smaller jugs?...

    How do you go about refilling the smaller jugs? With the fact that you have liquid to transfer...
  8. Replies
    84
    Views
    3,913

    I've tested brazing 3/4" soft copper while...

    I've tested brazing 3/4" soft copper while flowing co2. I made sure to get it all glowing red hot, welded the joint, and cooled with a wet rag. Cut it open, and no oxidization was there. Like someone...
  9. Thread: Manometers

    by knave
    Replies
    22
    Views
    1,981

    510

    510
  10. Thread: Bluevac Question

    by knave
    Replies
    10
    Views
    860

    thanks, Jim. Yes, I have also noticed that, and...

    thanks, Jim.
    Yes, I have also noticed that, and I just never put it all together.
    But in my experience refer in the bluvac would cause to gauge to read low, not high. I thought (?) that vacuums on...
  11. Thread: Bluevac Question

    by knave
    Replies
    10
    Views
    860

    So will the effects of the co2 diminish as the...

    So will the effects of the co2 diminish as the vacuum is pulled?
  12. Thread: Bluevac Question

    by knave
    Replies
    10
    Views
    860

    Bluevac Question

    Is the vacuum sensor's accuracy adversely affected by carbon dioxide gas?
    Edit: we've been using co2 for system pressure tests, and some have experienced quicker vacuum times as a result, so any...
  13. Replies
    21
    Views
    1,585

    So as a stand alone unit, it will not do tsh....

    So as a stand alone unit, it will not do tsh. Real time tsh would be the best, but I don't have an hvac guide or sman4.
  14. Replies
    21
    Views
    1,585

    The srh3 has a 38" probe.

    The srh3 has a 38" probe.
  15. Replies
    21
    Views
    1,585

    doesn't look like the sdp2 does target...

    doesn't look like the sdp2 does target superheat?? I may spring for the srh3.
  16. Replies
    14
    Views
    923

    Bluvac all the way. Very sturdy, Yet sensitive......

    Bluvac all the way. Very sturdy, Yet sensitive... If sensor is dirty it tells you... You can also recalibrate it yourself.... I have the uei version and it's great...
  17. Replies
    28
    Views
    1,876

    Anyone ever hook hoses to the ak direct with no...

    Anyone ever hook hoses to the ak direct with no manifold??
  18. Replies
    473
    Views
    39,096

    Hey Doug, how's it going? I just got the Ak900’s...

    Hey Doug, how's it going? I just got the Ak900’s out again for the first time in a while....had a coil changeout.
    They've been riding around in the truck all winter, -20F and tossed here and there....
  19. Replies
    12
    Views
    1,969

    That's good! Never heard that one...

    That's good! Never heard that one...
  20. Replies
    473
    Views
    39,096

    Post deleted by author....

    Post deleted by author....
  21. Thermocouples have a shorter life, in my...

    Thermocouples have a shorter life, in my opinion...
  22. Replies
    473
    Views
    39,096

    Funniest thing I've read all day!! LOL!

    Funniest thing I've read all day!! LOL!
  23. Replies
    473
    Views
    39,096

    When did the clamps become available?

    When did the clamps become available?
  24. Replies
    473
    Views
    39,096

    You'll never regret it...

    You'll never regret it...
  25. Replies
    473
    Views
    39,096

    That's a good one! Brent, you have put...

    That's a good one!

    Brent, you have put together a professional review. Also, I appreciate how you keep your cool in spite of the maturity level of some posts!
    I also own a set of AK900's, and I...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event