Search:

:oops: My Bad

i have changed many traulsen condenser fan motors as well as evap fan motors. some times the 9 watt 115v cw rotation motors would fit fine. but i have had a few where the 9 watt motors depth was to...

looks clean on the right side lol

i miss my like dislike Options

you can obtain new ends from hoshi.

im looking for a job in ct. have 17 plus years of refrigeration Experience.

These units are just like the window shakers. just toss them out and get a new one .its all about how cheap they can sell them.

Lentil Beans :grin2: makes the best gas

i used to carry about 8 differant flavors if not more on my van. i now have 5 . and most units are not marked whats refrigerant was put in them. so when i dought i sawp it out and mark the unit what...

the top side of the Evap looks like its all gummed up. Bad air flow ?

try a mechanical bin control extension solved a bunch of new hoshi.ice up problems for me

hide a trail cam and video it

United sells Super Blue good to -30 degrees

recover charge and weigh the amount that you recovered. and start from there

mp39

Just use 408 and be done with it

clear the ice around the drain with a torch then hookup a good garden hose and use hot water make sure drain is clear
and unit is off. and deice you can feel the water temp coming from the coil if...

evap coil looks like it needs a good cleaning also this will help air flow

the ones i serviced did

correct me if im wrong isn't 407C used in A/C systems and 407A used in Refrigeration systems . for r22 replacements ?

use brown rice its better

ditto easy fiix have to replace the entire glass

on your 5 th post you said they checked out fine ?

dual voltage unit ? 208 /230 volt unit .3 wire with a neutral leg ?

:deadhorse:

:cheers:

i do refrigeration work. not sure what part i want to move to any suggestions. and any good companies out there ? i have been in the field for 17 plus years.

check the voltage at the water inlet valve :gah:

i have seen the voltage drop out. and the water valve keep running water for a few seconds and over filling the sump area. and you pull the hose and see no water .your first thought would be the...

11 1/4 inches lol

the a/c vent is a no no above an open air case

when did you ever see a chest freezer with defrost just saying ?

and i don't blow off crap .

chipping the ice off will help the plate :whistle:

use the tips of needle nose pliers .i believe some service wrenches had them on them ?

who is paying for the repair you or the customer ? now add the prices of the oil changes ? how much more is it ?

just use 408 and be done with it
no oil change needed

united refrigeration sells .036 cap tube. # tc36 . i would have went with the bc2 .040 . .031 seems too small

It will take more than a few days to thaw. i have seen box's down a week and there still was ice when i took apart a box to relocate it . might want to put a few heaters in it to help thaw

low charge

use mp 66

the guy that i work with has and old one that ranco used to sell or give away .i have been looking for one my self i use a small hose clamp and attach the end to a Phillips screw driver then wrap...

what ever i use out of my truck stock .i keep the box top then when i go to the supply house . i restock what ever i used .

what kind of freezer M# S# ? i have seen the door pins get wet when unit in defrost . i believe it was a continentail . the drain line was pitched back making water drip on to box .not in pan

that's what i was taught also

they didn't pay the bill

just do what most hacks do . leave it hooked up to the unit and install another and use an acess tee on the service port . and be done with it or pinch off the line cut it free and braze the new one...

the hammer kisses are the dopes knocking the ice off the strips i would order new strips , heater , and be done with it they are sometimes hard to reinstall when they are banged up

i use nu brite for condenser coils. but you need to rinse it off well . and cal clean hd for the evap coil's

looking to get a refrigeration job in ct.i have 16 years in the field now need to move on before they close the doors on me. anyone hiring in ct area ?