Type: Posts; User: Clorox
Search took 0.01 seconds.
When they installed my AC/furnace, I wanted dampers. I saw them cutting pieces of sheetmetal, did not look like they came the right size? Looked like they manually made each with cutting snips?
A friend said that Trane Spine Fin Coils look like Snowflakes.
That this "snowflake" grabs dirt, dust, hair, anything like a brush, which is very hard to clean.
He said other coil types grab...
I bought some new air vent deflectors. I don't like them. They have only 2 magnets, one on each side. These two long magnets sit on top of the screw heads on the registers, causing the deflectors to...
Deflector facing up on the supply vent. I think, I tried that once, I will try again right now.
First floor, I have two tons and 4 returns.
The dining room has my thermostat.
Dining room has one supply and one return.
Supply is on the furthest wall. Return is on the wall between...
I see. So, BTUH is a measure of Heating.
What is the measure for cooling?
So 21" to 23" is leaving a bigger than needed empty gap.
Looks awkward/sloppy instead of being tucked neatly into the side of the house.
Kids will run back there, plenty of room.
As long as it's not a heat pump, they are only used for cooling.
How far from a home, minimum and maximum should an outside unit's base pad be? How far should that unit itself be from any wall?
From other things, other units?
I feel that my units are too...
Innerflow and conventional covers?
I think, that I want both my outside units covered when not...
My contractor is not interested. I told him what I wanted. I know trane sells the parts, my dealer told me the XB's do not have covers and that is that. I know that Trane sells them individually for...
The 2 ton has an orange thing wrapped around the compressor horizontally. Looks like a hot pocket?
The 3 ton has no wrapping.
What the hell?
So XB does not have it as an after market add on? Screw holes are there. Can I oder direct from Trane. Anybody have a web site or trane parts phone number? Trane does not seem to have a number on...
I don't think, that I was able to determine scroll versus recip.
Can someone tell for sure on the compressors?
It looks cheap, especially when you can see it clearly from the street/front of the home. Would look more professional complete look with the cover plate on.
The service corner has a top cover...
5:00pm 2nd floor, bedroom doors open
outside = 87
inside = 74 (lowest possible)
difference = 13
7:00pm 2nd floor, bedroom doors open
outside = 84
inside = 72 (lowest possible)
1) I should have gone to 3.5 tons.
2) I should have added a return vent in my hallway, right above my thermostat. (suck the trapped heat out)
The XB13 (R410a) comes minus the bottom service panel cover where the set line plugs in.
The XR does have the panel cover.
Does anybody know if they make a bottom panel cover for the XB?
I would like to get a whole house fan tent and attic hallway door tent? Something, anything to block the heat from penetrating my 2nd floor through my whole house attic fan vents and attic pull down...
What is the wet bulb?
Air penetration, could be.
Explain how the dew point works?
A difference of 26 degree's? How? Oversized? Too much freon?
I thought a differential of 20 was the max?
86 Outside and best Inside temp is 73. (2nd floor)
Difference of only 13 degree's?
New system, 3 ton Trane. (been running all day non stop)
6 returns and 10 supply vents.
What is the diff between input and capacity BTUH?
4 speed blower means I have 4 choices?
3 burners versus 4 burners?
Why not have both identical systems? Seems like they wimped me out on the...
5” Media air cleaner
System uses R 410a non ozone depleting refrigerant.
Refrigeration line set.
Arrive at 9:00am and leave at 3:30pm
Two days for the 2nd floor and two days for the first floor.
Is this normal?
No, I used the same original location. Swapped an analog for a digital. Stat is on an inside wall, the adjacent wall has the return. I think that return is sucking all the cool air out cause it is...
The warranties are the only diff? There has to be more?
The compressors are diff?
I don't know but 5 tons is huge! Haha. What is your footage? Just curious.
(Talking about R410a type units...)
1) What are the exact specific differences between the XB13 and XR13 condensors? Is it marketing?
2) What about the two basic furnaces? XB80 and XR80?
1) Crawl Space.
2) Stat is on an inside wall.
3) I don't know? I ran some wires through the sheetrock and connected the Stat myself.
Can you explain the correct procedure? I am clueless.
I need to buy 2 furnaces and 2 AC condensors.
1257 square feet Downstairs
1660 square feet Upstairs
(These are my bids... they all include two basic conventional furnaces and two 13 SEER...
If I want to add some ducts, will they be Flexi ducts or do they still make Rigid ducts? My old ones are rigid?
I have one duct that connects to three supply vents. The front foyer, the dining...