Search:

Type: Posts; User: generaltech1

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    455

    Hobart 2912 slicer

    This slicer no longer works in auto mode. I was wondering what I need to look for on this, is it merely just a switch? I had this apart about 3 weeks ago to replace the on/off switch and I really...
  2. Replies
    4
    Views
    517

    I did trace the wires and the donuts are...

    I did trace the wires and the donuts are connected to the controller. Thanks
  3. Replies
    4
    Views
    517

    Metasys CT

    Ok, having mainly a residential background, not having to have dealt with this before, I need some advice and/or guidance on how to correct an issue with a building's CT that shows that its offline...
  4. Replies
    23
    Views
    1,662

    Ive heard of Tony MacAlpine, but never heard/seen...

    Ive heard of Tony MacAlpine, but never heard/seen him play, until now! He kicks ass!!!
  5. Replies
    13
    Views
    3,829

    Ive so far found that the cooling fans were CAKED...

    Ive so far found that the cooling fans were CAKED with grease and dust, im going to clean them first. And follow up with all your suggestions. Thanks!
  6. Replies
    4
    Views
    834

    After replacing every component in the ignition...

    After replacing every component in the ignition system, it lights, but goes out immediately! I would say flame sensor, but that has been replaced as well!!
  7. Replies
    4
    Views
    834

    Groen Smart Steam

    M: SSB5G S:J77748B-1-1
    This dang steamer has been a bur under my saddle for the past year, luckily their are three others that they can use. I have gone thru this unit with a fine tooth comb,...
  8. Replies
    19
    Views
    1,621

    That's another thing...I have never...

    That's another thing...I have never reallyunderstood sh/sc...can someone splain it in english?
  9. Replies
    19
    Views
    1,621

    Gauge Reading

    Ok yeah Im not that good at reading my gauges, I admit that, but here goes. R22, 91*ambient, suction 75#, discharge 300#, low on refrigerant? Im only getting about 60* DA temp. Room temp is about 76,...
  10. Replies
    2
    Views
    828

    Groen SSB5G

    Im desperately looking for an actual service manual for an SSB5G/J777-48-B-1-1, not the operator manual. Anyone out there have a link to get one or have one that can be emailed to me? Thanks in...
  11. Replies
    13
    Views
    3,829

    Ill check into that.

    Ill check into that.
  12. Replies
    8
    Views
    1,112

    The 1st one had a blown out relay on the fan...

    The 1st one had a blown out relay on the fan timer, but when I replaced it and the motor was finally getting power, it sounded bad. It took off slow, and ran for a while, unitl tstat was satisfied...
  13. Replies
    8
    Views
    1,112

    yes 24v to the module

    yes 24v to the module
  14. Replies
    13
    Views
    3,829

    Blodgett DFG1XL/AA

    S/N 092107RI0492-Ive had numerous calls on this unit, but I cant ever find a problem with it, yes the dreaded intermittent problem. Although the last time that I was there I set it to 350F, and...
  15. Replies
    8
    Views
    1,112

    pressure switch is closing

    pressure switch is closing
  16. Replies
    8
    Views
    1,112

    On the first unit, open limit @ hx, I jumpered it...

    On the first unit, open limit @ hx, I jumpered it out, it lit off, no power to motor on com and high. So I guess I need a board for that one.
    And on the 2nd unit, indoor blower operates, combustion...
  17. Replies
    8
    Views
    1,112

    Two ICP RTU gaspacks

    1st one PGME60H150C/G030612118..thermostat blank, all that's running is the combustion fan motor, no call for heat, got 24v into the control board, but nothing on any of the lv terminals on the...
  18. Replies
    2
    Views
    1,215

    CresCor warming cabinet H137UA12C208

    I get a call that its not heating. It has a tag on the back stating "Wired for 208 Volts", but no where am I getting 208V only 120v. I called CresCor tech support since I didnt have any tech...
  19. Replies
    3
    Views
    1,724

    Blodgett oven calibration

    Model #: DFG-100-XCEL-DOUBLE. I was wondering if somehow this oven is calibrated differently than others, and if so, what is the correct procedure. I have calibrated a variety of ovens over the...
  20. I know that this thread is well over 5 years old,...

    I know that this thread is well over 5 years old, but it doesnt hurt to ask. I was also looking for a copt of the Maple-Chase 9700 thermostat manual, if anyone out there has a copy, give me a shout....
  21. Replies
    2
    Views
    728

    Trane on Metasys

    Ok ill try to make this short as I can. I have little experience on commercial and no training or experience with Metasys. These are Trane package units of various sizes that are cooling...
  22. Replies
    12
    Views
    794

    What are your thoughts.........

    As a group, what are your thoughts on a fellow employee that runs to the boss every time they have a "problem" (the problem being a comment made jokingly, and not a comment of a suggestive or...
  23. Thread: US Range

    by generaltech1
    Replies
    2
    Views
    936

    US Range

    I cannot seem to find a model and/or serial # on this unit. Can anyone tell me where I might be able to find it? Its about 10 years old(guesstimate). The problem is that the pilot wont stay lit...
  24. A bobcat walks into a bar...............

    Youve got to see it to believe it:
    http://www.myfoxphoenix.com/dpp/news/Bobcat_Attacks_Inside_Cottonwood_Bar
  25. Replies
    3
    Views
    769

    Ahem....well thats 1:47 of my life i'll never get...

    Ahem....well thats 1:47 of my life i'll never get back, thanks.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event