Search:

The only HTML5 was if the grid pane had a part not reporting it would crash the html5 that was fixed in4.6

if the comm card is a lon card you must bind it in lon Rover

are you using the latest version of Trane Rover

are you using a jace if you are the chiller should be biased with a one hundred ohm resistor if the blue wire if purple an 82 ohm resistor had the same problem. i was also burning out the lon boards...

johnson is 62 if using n2 buss 32 if using mstp took the course

Ihave taken the bacnet spyder class with john hutchey and was told they are 1\4 load but the max allowed is 31 jace is 1 makes 32. iwas also a webs installer and have ckeaned up jobs that installing...

How many MSTP buss only allows 31 devices and jace counts as 1 . a busy time over 60 is no good. there is no fudging that number at all Tridium will not talk to you with over that number.

for old jace 545 and 403 56 k

115k 8 none 1 no flow control

should have said reboot your laptop

If software is below 3.6 just file transfer over the spyder and venom tool jar files and reboot jace if above you need the installer but to just open and view them just transfer spyder tool jar and...

yOU CAN ALSO CHANGE THE DEFAULT USER NAME AND PASSWORD HAVE RUN INTO THAT BEFORE IT WILL DRIVE YOU CRAZY TILL YOU REALIZE THAT SOMEONE CHANGED THE DEFAULT TO THEIR OWN

Tridium user niagara password as long as it was not changed find config.bog file open user in services add yourself as superuser and recomission station you now have superuser access

If jace says honeywell comfort point its factory and closed good luck trying to get factory to open it other two are honeywell webs open and closed you can get honeywell to open these with a letter...

did you set the bacnet instance id to a different one before you put them on the network all spyders come with the same instance id got me the first time
this is different than the mstp address

infocon makes a cbus driver that works very well you flash the easyio 30p and it sends the data to a jace

It is digital tone modified frequency or modem audio

Yes it could be a big deal as long as it is comm3 isolate ie not polarity sensitive already have driver for the comm3 non isolated ie polArity sensitive

The interface is a torroid transformer the protocol is audio just as modem audio that is the data highway

i tried to email you the answer but your email bounced email me at dlhvac@ptd.net

i use an infocon easyio 30p or a spyder micro

the sensor has the output rating right on it i cannot recall offhand but the bypass damper cannot be controlled by the jace you must replace this controller with another the ccp panel previously...

yes but usually the supply house you purchase the driver from is the first contact i use broudy supply in philadelphia, also cochrane supply in mich has the driver

worked well have done a bunch since then 12 or 13

9600 8 none 1

broudy supply in phila has the drivers

yes it is available thru maxline drivers with infocon support for 10 years

Does the install have trane purple wire if not your on your own

Approx 80 or more points per rtu all the diagnostic alarms and you can also reset diagnostic faults

You can see more of the voyager and reliatel points than with tranes software

The zoning and rtu overides are done in the jace

I would use a six if you are putting graphics on it if noy jace 2 should work watch your java heap and busy time on the jace comm four is a reource hog

Sorry but i dont give away stations that ive done but it is doable to integrate all that you stated

Maxline drivers owms the comm4 driver infocon sold the driver division go them but has a contract for 10 years to provide support

worked very well have done 12 to date

you have to put the unit in tracer control and command the input mode

the ashrae show sent you an email

the ashrae show

THE CONTROLLERS WILL BE OUT AT THE SHOW IN DALLAS IM BETA TESTING A PROTOTYPE

Have over 50 installed at different sites all work flawlessly and yes they talk sedona modbus and bacnet all at the same time the new ones due out will have its own html5 graphics engine and it own...

Forgot using lon requires the firmware in chiller to be the latest Trane will have to upgrade recommend using comm4

There are some issues with the commissioning of the lci-c chiller lon cards you have to set the response to the jace at no response to commission because some of the cards do not send this response

looked this up you should be able to get lon cards for these lci-c

sorry should wear glasses when reading messages you wrote chillers what comm card is in the chillers now i believe a comm 4 card is available
for these chillers

The rooftops have a trane tci board if you rotate the daughter board 90 degrees it becomes comm4 instead of comm3 isolated this is integratable to a jace with an infocon comm4 driver

This is what the 20 ms intermessage delay fixes:cheers::cheers:

ps on the serial port setup in the intermessage delay set it to 20 milliseconds on all infocon drivers ( did the beta testing on the comm3 driver works great)

also if you cant read the temp sensors try bringing the voyager in as a different voyager either 1, 2 or3 1 is for old style single board 2, and 3 are reliatel boards

when you bring the points into niagara before you name it look at the facets it says which enum you must write for each voyager function use the ax communtiy jar found online
because you need to...

Go to the spyder school but get tridium certified first its required