Search:

Type: Posts; User: 1adam12

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    431

    Goodman HP Defrost Board issues

    I installed a 14 goodman HP a several years back, the past 3 years i have had to replace the defrost board. The failed boards do not show any physical damage, it just will not go into defrost. Line...
  2. Replies
    19
    Views
    11,266

    wrong, trane is not partners with american...

    wrong, trane is not partners with american standard. hasnt been for about 3 years now
  3. Thread: cheat sheet?

    by 1adam12
    Replies
    19
    Views
    1,598

    nor is he in compliance with EPA for not keeping...

    nor is he in compliance with EPA for not keeping refrigerant records. just sayin...
  4. depending on wire and if its comm 5 he would read...

    depending on wire and if its comm 5 he would read 40-75ohms, closer to 0 is open ie: no EOL resistors or cut/damaged wire
  5. thats true but he didnt say so i only assume. And...

    thats true but he didnt say so i only assume. And i have a 11 yr old site thats comm 5, i think he mention 5 yrs old on his.

    To the OP, right click on a graphic and click edit, in the setup tab...
  6. Replies
    14
    Views
    3,437

    I agree with mallron, most mechanical/electrical...

    I agree with mallron, most mechanical/electrical installers trash or misplace the cd's. And if you would have not offended Trane employees on this site b/c your being a bad a$$ behind a keyboard I...
  7. do they have a NID assigned to them?

    do they have a NID assigned to them?
  8. you will need to get a upcm cable and a cpu with...

    you will need to get a upcm cable and a cpu with BCU IP config to upload the ip settings in the BCU, and as far as the units your not talking to. they could have been powered off for a prolonged...
  9. Replies
    7
    Views
    1,231

    thanks email sent, yes i use rover configed for...

    thanks email sent, yes i use rover configed for Lon4
  10. Replies
    7
    Views
    1,231

    thanks for the help but im still a bit lost where...

    thanks for the help but im still a bit lost where do i go from here?

    http://i160.photobucket.com/albums/t188/adamrich33/NodeUtil.jpg
  11. Replies
    11
    Views
    2,003

    this is a well explained answer, follow his...

    this is a well explained answer, follow his advice. the above reply was a bit vague and useless.
  12. Replies
    2
    Views
    587

    if you are reffering to a vfd, the transducer...

    if you are reffering to a vfd, the transducer gives the controller a static reading to which the vfd/controller will ramp up and down at a given setpoint. typical transducers give a output dc voltage...
  13. Replies
    4
    Views
    1,546

    got a serial?

    got a serial?
  14. Replies
    7
    Views
    701

    isnt that setpoint adjusted at the module on the...

    isnt that setpoint adjusted at the module on the unit
  15. Thread: Bmtx pcm Trane

    by 1adam12
    Replies
    2
    Views
    480

    try a database and clear,ram reset.

    try a database and clear,ram reset.
  16. Replies
    7
    Views
    701

    oh, the site i was referring to is running...

    oh, the site i was referring to is running 3.4.43, might want to give niagara a call.
  17. Replies
    7
    Views
    1,231

    what nodeutil version do you have, mine will try...

    what nodeutil version do you have, mine will try to run but as soon as it opens it will close down.
  18. Replies
    7
    Views
    1,231

    Node Util for Windows 7?

    Anyone have windows 7 running node util via echelon usb adaptor?
    i have also lost my function of hyper terminal.
  19. Replies
    7
    Views
    701

    ive seen it with LCIRs before, like you said,...

    ive seen it with LCIRs before, like you said, delete and rediscover always resolves that. Not sure what the deal is, however i have seen tridium panels installed with a termination module on the...
Results 1 to 19 of 24
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event