Search:

Yep FRP is the answer and use the plastic rivets to make it look nice. Will make the box look brand new. The health dept will get off their back if you reline the whole box with it. Haha 30' X 60'...

Regardless of where your problems is to answer your question, you don't have to take out the evap to pull out the gear box. I just did it on a machine I got in my garage last month. Just try to...

3 beeps is freeze back up timer (over 60 minute freezer). If you pulled the boot and the float was still showing closed I am sure this was probably the cause.
Tip: Usually after I clean out the...

good tip thanks Dave

Yeah the local taylor service company said water should work just fine but the 430 has a wash option on the toggle switch that takes all this out of the lope so it must read different. Thanks for...

I think they were Yellow Jacket's he was talking about. Don't know the guy very well but it was funny that you asked because he just mentioned it a the parts house that day.

I have seen many LLSV installed backwards but never a TXV. If I saw that I would tell the customer I'll be back and go buy a camera. Damn that would be wicked hard to do even. The guy who did it...

There lucky they didn't lose those compressors. Running close to 400 with controls bypassed. Some one could have cost them some big cash.

Problem solved. Put Margarita mix in the machine instead of water and the unit functions just fine. Water wasn't conductive enough. Either was the sugar water that I tried putting in the machine. ...

The wee little 13 lb. tank of HP81. It's in 13 lb tanks cause you'll only use it every couple of years. If it was 502 I would replace it with FX-10. I have done this many times and never had any...

Put in a Mohave and have had lots of issues with the controller, very elaborate valve layout and controller. Many error codes resulting in shut downs. Not super impressed so far.

If it's an Ice-O-Matic and it's broken it's pretty much doing what it was built to do. I saw one in Mexico on vacation it was called a Torro Rey, I don't speak spanish but I am sure this means Bull...

I agree with 76olds, run it into a defrost and check amperage and voltage, if you have power into the limit but not out and the coil is iced up then you need a new limit (if totally iced).

Not sure on the G model but I am pretty sure that before the S models the first 2 digits of the serial # was the year it was manufacuted. I would use FX-10 if I did the repair. I don't carry one...

I like the quality of the Kairak units I have worked on. They seem to have there ducks in a row. Have talked to tech support a few times and they seemed knowledgable. I have only worked on one of...

Haven't heard good things about the solar gauges. Was just talking to a guys yesterday that said he had some and his quote was "if you keep them in the case and don't take them out till ya use them...

noticed the new packaging on the 8145-20, I like how they have to put the picture on the box now since the language barrier (with the manufacture) could cause them to put the wrong item in the box.

Has his production increased, maybe he is pulling the product sooner than he used to. Faster turn around time. Just a thought.

40-55 psi suction pressure in a harvest cycle is to low. Should be min 70 to about 90. Going off memory and what I see most of the time. But for starters thats a problem. Now you just got to...

Yep I already replaced the probe. I contemplated the possiblity that the board was defective but as I said, just by setting a wash on top of the probe it fires the machine, or by grounding it to the...

The probe is just a steel bar, with a round metal top. There is no internal workings to it. The probe is mounted in the bottom of the hopper isolated from the hopper with plastic. It appears to...

I have been working on a Taylor Model 430 and the problem I am having is the mix light out probe which shuts the machine down on a safty. I can make the machine operate by either:

1. Grounding...