Search:

Type: Posts; User: H-Tech

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: hobart parts

    by H-Tech
    Replies
    27
    Views
    6,205

    Gcs buys parts from Hobart and marks them up. My...

    Gcs buys parts from Hobart and marks them up. My Buddy works for eco-lab. Also you can find Hobart diagrams on line at hobart.com
  2. Replies
    7
    Views
    1,525

    Call you local Hobart service office and they...

    Call you local Hobart service office and they will be glad to repair under warranty if properly installed. Hobart does vulcan warranty.
  3. Thread: HOBART

    by H-Tech
    Replies
    3
    Views
    632

    These boxes are obsolete. Most of the components...

    These boxes are obsolete. Most of the components are off the self at most ref. supply houses.
  4. Replies
    5
    Views
    1,076

    sounds like out of calibration or t-stat.Is this...

    sounds like out of calibration or t-stat.Is this the T-stat that has the chain coupling you have to adjust like old pitco?
  5. Replies
    3
    Views
    1,763

    Check to see if the centrifical switch is closing...

    Check to see if the centrifical switch is closing in the blower . It is a normally open switch that closes when then the motor runs .This is a common problem. This feeds the spark module to produce...
  6. Replies
    7
    Views
    5,262

    It is probally an adamatic oven

    It is probally an adamatic oven
  7. Replies
    28
    Views
    3,868

    I like Hobart Tech support. Those guys are always...

    I like Hobart Tech support. Those guys are always friendly and helpful to me.
  8. Thread: Hobart Techs

    by H-Tech
    Replies
    2
    Views
    1,077

    It has it's good benefits, heck good...

    It has it's good benefits, heck good insurance.You will get some factory training on branded equipment. This will give you a good base for competitive equipment.I don't think I would want to be a...
  9. Replies
    28
    Views
    3,868

    Our business has been a little slow. We do full...

    Our business has been a little slow. We do full kitchen equipment plus refrigeration. We do factory service and other brands. that helps to keep busy. Kitchen equip. is not that bad to service but...
  10. Thread: hobart mixer

    by H-Tech
    Replies
    2
    Views
    1,426

    That is unit has an ac drive in it. suspect issue...

    That is unit has an ac drive in it. suspect issue is bus fault.
  11. Replies
    4
    Views
    1,020

    When you cleaned off the char it opened up the...

    When you cleaned off the char it opened up the pores and made griddle non-stick. You will have to season the unit with some grease and build back up some carbon. That should take care of your problem.
  12. Replies
    52
    Views
    6,162

    Sorry it took so long to get info. I had to go to...

    Sorry it took so long to get info. I had to go to the shop and I found info. It ia part number 855400-1 burner enhansment kit. The price of it is $1718.90. It comes with some paper work with it to...
  13. Replies
    52
    Views
    6,162

    I'm gonna jump off here I'll try to find those...

    I'm gonna jump off here I'll try to find those numbers for you and post this weekend. It may be first of week if I can't find in truck.
  14. Replies
    52
    Views
    6,162

    Like I said I have to fly under the radar. ...

    Like I said I have to fly under the radar. Company does search sites and we get called in and reamed for info giving out info.
  15. Replies
    52
    Views
    6,162

    Kinda it hangs in the tank does same job

    Kinda it hangs in the tank does same job
  16. Replies
    52
    Views
    6,162

    Easy on the hsm. These things can be a money...

    Easy on the hsm. These things can be a money pit!!!!
  17. Replies
    52
    Views
    6,162

    Wait till you have to put a boiler tank in the...

    Wait till you have to put a boiler tank in the unit and if it is used alot with out filtration on water(hard water) you will need one it is about 100.00 cheaper than the whole steamer new. I have...
  18. Replies
    52
    Views
    6,162

    Almost sure of the size. i take them off don't...

    Almost sure of the size. i take them off don't pay much attention to them. I sure either 10/24 or 10/32.
  19. Replies
    52
    Views
    6,162

    I can get that number for you and I pretty sure...

    I can get that number for you and I pretty sure of price. It may be more.
  20. Replies
    52
    Views
    6,162

    You talking about the 10-24x1/2 that they are...

    You talking about the 10-24x1/2 that they are about 6 of them phillips head on the round ring.
  21. Replies
    52
    Views
    6,162

    That was one of the improvements made to correct...

    That was one of the improvements made to correct burner miss firing and bad harmonic. Was moving the air sense on this unit.
  22. Replies
    52
    Views
    6,162

    Another thing to keep the phennalic tube on you...

    Another thing to keep the phennalic tube on you will need to wrap teflon tape to keep it in position or it will fall off. That will give you air problems.to get new style burner with air pick up up...
  23. Replies
    52
    Views
    6,162

    is it picking up the combustion proving on the...

    is it picking up the combustion proving on the phenalic tube around the flame rod ? This has a hole in it and the pressure is suppose to go through and it has to be in the up position. that is the...
  24. Replies
    52
    Views
    6,162

    Thats cool I I have to fly under radar due to who...

    Thats cool I I have to fly under radar due to who I work for. They frown on us giving out to much info.
  25. Replies
    52
    Views
    6,162

    send me your number and i give you a call to see...

    send me your number and i give you a call to see If I can help more.
Results 1 to 25 of 80
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event