Search:

Type: Posts; User: ssseward

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    671

    also have seen steam driven eductors used to...

    also have seen steam driven eductors used to speed up evacuation time on large absorbers.
  2. Replies
    3
    Views
    671

    Saw it on a turbine drive chiller. Helped the...

    Saw it on a turbine drive chiller. Helped the turbine use steam better and put it through a heat exchanger to use the heat for something else afterwards.
  3. Replies
    28
    Views
    2,179

    Cant believe you all missed it, The problem is...

    Cant believe you all missed it, The problem is the bull nut is loose on the heifer shaft.
  4. Replies
    15
    Views
    1,022

    NOT TO MENTION THE FACT THAT A SCROLL RUNNING...

    NOT TO MENTION THE FACT THAT A SCROLL RUNNING BACKWARDS IS NOISY AS HECK
  5. COULD YOU USE A REGULAR MACHINE AND USE SOME OF...

    COULD YOU USE A REGULAR MACHINE AND USE SOME OF THAT FREE WASTE HEAT TO HEAT THE LEAVING COOLING WATER?
  6. Replies
    7
    Views
    2,120

    We have repaired leaking tube sheets by sand...

    We have repaired leaking tube sheets by sand blasting the tube sheet, putting the machine in a vacuum, and using belzona molecular metal or epoxy on the tube sheets and waterboxes. The only problem...
  7. Replies
    121
    Views
    11,866

    If Your Not Doing Anything Wrong, What Differance...

    If Your Not Doing Anything Wrong, What Differance Does It Make?
  8. Thread: U tube

    by ssseward
    Replies
    15
    Views
    1,759

    All That New Stuff Is Ok As Long As Its Not...

    All That New Stuff Is Ok As Long As Its Not Adding A Chemical Into The System That You Cant Get Back Out. And Why Would You Want To Use A Water Based Manometer And Add Moisture To A System Other Than...
  9. Replies
    5
    Views
    666

    We found parts of the curcuit wiring layng on the...

    We found parts of the curcuit wiring layng on the ground and in the water after it rains so we got it up, dryed it out and it solved the problem till we can replace the wiring harness. thanks
  10. Replies
    5
    Views
    666

    rtac fuse blower

    I have a rtac that runs fine loaded but when it unloads, it blows the control fuse. It dosnt matter which circuit is running either. Anybody have any ideas? Thanks
  11. Thread: coelescers

    by ssseward
    Replies
    1
    Views
    396

    coelescers

    Anyone Know Of A Good Place To Buy Coelescers For A Reco Screw Package?
  12. Replies
    11
    Views
    858

    ambient air temp is 93. the cond. coils were...

    ambient air temp is 93. the cond. coils were cleaned first, but they are getting a little ragged. all the fans are running and ok. I was suspecting worn bearings or rotors adding the extra heat. ...
  13. Replies
    11
    Views
    858

    Thanks a million. I will see what it looks like.

    Thanks a million. I will see what it looks like.
  14. Replies
    11
    Views
    858

    That makes sense. Does too much oil mean higher...

    That makes sense. Does too much oil mean higher heat?
  15. Replies
    11
    Views
    858

    RTAA OIL COOLING Question

    I have a RTAA 100 with high entering oil temp on 1 circuit. The oil cooling circuit is dropping the oil temp 30 degrees. Oil into the oil cooler is almost 190 degrees. sub cooling 20, superheat...
  16. Replies
    6
    Views
    919

    you might have a guide vane blade that has spun...

    you might have a guide vane blade that has spun in the pulley and is not closing with the rest of them, loading the compressor o start-up. ive dealt with that on xr's and earlier carrier centrifugals
  17. Replies
    8
    Views
    785

    Those molex connectors are definantly a suspect....

    Those molex connectors are definantly a suspect. ther is an upgrade kit from carrier p/n 32mp660-015. also, be sure you have a good panel ground
  18. Replies
    12
    Views
    3,437

    York Manual 160.80-m1(604) Has All The Info On...

    York Manual 160.80-m1(604) Has All The Info On That Panel And Display. Its Avail. Online At York.com
  19. Replies
    11
    Views
    958

    P.s 19dg

    Some DG,s had a float evaporator feed with a solonoid-piston arangement that opened the float at low load and some had a poppet valve that worked off of diff. pressure.
  20. Replies
    11
    Views
    958

    19DG Agitator valves

    19DG agitator valves were for low load surge protection and to stop the low load rumble DG's were famous for. they were brought on by a switch on the back of the vane motor. Most 19 DG approach's...
  21. Thread: Question???

    by ssseward
    Replies
    4
    Views
    678

    motor

    Sounds to me like someone got in a bind as was trying to make something work. Get a three speed and and simplify everything
Results 1 to 21 of 30
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event