Search:

Type: Posts; User: cjpwalker

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    650

    Hmm ...and it's a Goodman. weird.

    Hmm ...and it's a Goodman. weird.
  2. Awesome! I've seen most of these and experienced...

    Awesome! I've seen most of these and experienced others. Never seen the bleed port, though, or a metal hard hat.
  3. Thread: Wiring Fail

    by cjpwalker
    Replies
    11
    Views
    1,211

    Larger electric heat kits (usually over 10kw) are...

    Larger electric heat kits (usually over 10kw) are fed on multiple circuits and have two or more double pole breakers at the air handler. A single point kit is usually a molded plastic jig with...
  4. Replies
    12
    Views
    384

    From family or the pawn shop like we all did when...

    From family or the pawn shop like we all did when starting out.
  5. Replies
    8
    Views
    437

    Two or three Thanksgivings ago somebody turned...

    Two or three Thanksgivings ago somebody turned off the oven. By the time the bird was done it was after 10pm and everyone was full of snacks and pie. I wasn't paying attention and didn't notice it...
  6. Manifold pressure stays up above 9? So you...

    Manifold pressure stays up above 9?

    So you have a rollout... It's either a blocked HX or flue, not enough primary air, not enough gas, or negative pressure in the boiler room (exhaust fan,...
  7. Replies
    12
    Views
    1,265

    Close - it's an enterprising startup of a...

    Close - it's an enterprising startup of a Voyager...
  8. Replies
    11
    Views
    262

    QUOTECEPTION... mmmwahaha

    [/QUOTE]

    QUOTECEPTION... mmmwahaha
  9. Replies
    26
    Views
    903

    Hittin' the sauce a little hard tonight?

    Hittin' the sauce a little hard tonight?
  10. Replies
    26
    Views
    903

    Said it's a new machine - they usually come with....

    Said it's a new machine - they usually come with. Otherwise it's 30 to 45 seconds to locate it on the manufacturer's website... RTFM!
  11. Replies
    26
    Views
    903

    The machine won't recover if it is set to purge. ...

    The machine won't recover if it is set to purge. This is for purging refrigerant from the machine.



    If the gauge is pulling into a vacuum then there is no refrigerant getting to it.

    Did you...
  12. Replies
    37
    Views
    8,146

    I recently got a couple of Dan Holohan books -...

    I recently got a couple of Dan Holohan books - great reads. I've been spending my time in the water closet learning about the Lost Art of Steam Heat. Seems appropriate...
  13. Thread: Brixing

    by cjpwalker
    Replies
    15
    Views
    648

    Your Coke rep should be more than helpful. ...

    Your Coke rep should be more than helpful. Otherwise, the Pepsi rep might!
  14. Replies
    39
    Views
    2,046

    ...and there you go.

    ...and there you go.
  15. They have killed Americans - chopped their heads...

    They have killed Americans - chopped their heads off and put it on the internet. So should we not kill the 10,000 then?
  16. Replies
    2
    Views
    201

    The manual is not very clear. The board on the...

    The manual is not very clear. The board on the air handler can tell if you are in heating or cooling mode - it sees the signal from the thermostat. In heating mode it will ignore the profile. In...
  17. Replies
    45
    Views
    3,227

    Bottle cap filters...

    Bottle cap filters...
  18. Replies
    21
    Views
    1,354

    Hmm. Not going to say I'm disappointed, but you...

    Hmm. Not going to say I'm disappointed, but you know when you see your favorite Radio DJ for the first time...
  19. Replies
    29
    Views
    1,004

    Other than the crossover which it most likely...

    Other than the crossover which it most likely needs, there's usually not much you can do with ductwork. Its tucked up above the frame under the insulation.
  20. Replies
    5
    Views
    362

    You think it would hold? There's stress on that...

    You think it would hold? There's stress on that joint, and I know employees like to wrench those knobs down pretty tight - we replace a cracked face plate or two every year.
  21. Replies
    10
    Views
    387

    Whoops - I missed where the GFCI was directly...

    Whoops - I missed where the GFCI was directly shutting off the furnace - I assumed it was the condo pump overflowing and tripping the safety... Yeah - the thing is wired wrong - the furnace should...
  22. Replies
    17
    Views
    726

    .

    .
  23. Replies
    17
    Views
    726

    Maybe - but at this point the sparkies, the code...

    Maybe - but at this point the sparkies, the code book and the AHJ are all satisfied.

    This building has 7 split ac's - 5 ton lennox with LG scrolls. The three on the west end near the electrical...
  24. Replies
    10
    Views
    387

    We had issues a few years back with Beckett brand...

    We had issues a few years back with Beckett brand condensate pumps and gfci. Since switching to a different brand that problem has gone away.
  25. Replies
    29
    Views
    1,004

    How is your drain line configured - trap? vent?

    How is your drain line configured - trap? vent?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event