Search:

Type: Posts; User: CerealKiller

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    496

    Ah! Thanks! Boxed myself into the thought of...

    Ah! Thanks! Boxed myself into the thought of needing an "action" to manipulate it.
  2. Replies
    7
    Views
    496

    No, there are earliest start time and earliest...

    No, there are earliest start time and earliest stop time settings within the (VykonPro) OSS block that use AbsTime. Trying to figure out how to expose them.
  3. Replies
    9
    Views
    436

    Have you verified the configuration in the...

    Have you verified the configuration in the router? I'd would also try connecting to it locally at the JACE with a good patch cord and see if it comes online......would verify your Ethernet...
  4. Replies
    7
    Views
    496

    Tridium Custom Programs

    Was trying to find a way to write AbsTime into the OSS blocks for start & stop times to expose on graphic. Haven't seen a way yet, but I know there is a RelTime command block in the VykonPro module....
  5. Replies
    7
    Views
    401

    Seems that the weather.jars work for a while,...

    Seems that the weather.jars work for a while, then just crap out. We have had some 3.4.43 stations constantly re-boot because of an issue with this jar. There are alternatives. I believe google...
  6. Replies
    10
    Views
    637

    Thanks smmedlin! Found our TUNCOS logic and...

    Thanks smmedlin!

    Found our TUNCOS logic and NDIO point polling eating it up. Also, set the Non-Critical Flag for the runtime extensions.
  7. Replies
    10
    Views
    637

    E Series JACEs

    Seems to me that Honeywell's genius idea to eliminate the need of batteries is to have the unit constantly process data recovery and hog up resources. These JACEs are slow, slow, slow....

    Is...
  8. Gotta love DIY'ers......first off, JACE needs to...

    Gotta love DIY'ers......first off, JACE needs to be licensed for "LCDProgrammable". Is he able to access that palette and set-up comms?
  9. Replies
    26
    Views
    3,455

    I discovered as a dynamic device and converted...

    I discovered as a dynamic device and converted the XIF file from the lonmark site to lnml. Program IDs matched. Wouldn't commission in AX though, but was able to config online and bring it...
  10. Replies
    26
    Views
    3,455

    Digging up an old thread......but having similar...

    Digging up an old thread......but having similar problems here with the LCI-R card.

    I too noticed nciOAMinPos coming in as SNVT_temp_p, instead of SNVT_lev_percent. I also do not see any change...
  11. Replies
    5
    Views
    530

    The points are selected for view. I have several...

    The points are selected for view. I have several conditions that must be true before I enable a fan, yet I always have one or two of them giving me a -1 value instead of a 0.
  12. Replies
    5
    Views
    530

    I referenced Vern's Level II Webs class booklet. ...

    I referenced Vern's Level II Webs class booklet. He mentioned that in an XL10 controller, you have to write a non-zero value to each of the data fields for the point to actually turn on. Not true...
  13. Replies
    5
    Views
    530

    Sharing binary status on Spyders

    Hoping someone can help me out here...

    I created nvo and nvi by using NV Config view in the Spyder (set to SNVT_switch). I exposed the state on the wiresheet and linked my logic. Generated NVs. ...
  14. OK. Created a nvo (temp p)and linked it directly...

    OK. Created a nvo (temp p)and linked it directly to the physical point. Created a nvi (temp p) and lon linked like mentioned above on the lon network wiresheet. Link worked.

    I do not see...
  15. I did the conversion and it took care of the...

    I did the conversion and it took care of the error. I have a nvoOATemp point in the points list, but it still does not show up when I go to do the lon binding on the lon network wiresheet.
  16. Spyder Programming Help - OAT Sharing

    For the life of me, I can't get the process down on how to do this. Any help would be appreciated.

    I have an OA Temp Sensor on UI1. I generated NVs, then went to Lon Point Manager. Located UI1...
  17. Replies
    5
    Views
    425

    Thanks for clarifying that Sam. I know Echelon...

    Thanks for clarifying that Sam. I know Echelon recommends that on their network, but really didn't occur to me about doing the same for DIs.

    Our vendor recommended Citel DLA.
  18. Replies
    5
    Views
    425

    Thanks for the replies. Will try wiring the...

    Thanks for the replies.

    Will try wiring the closer buildings direct and go with the relay solution on the farthest.

    Osiyo, thanks for the controller operation explanation.
  19. Replies
    5
    Views
    425

    DI line length

    I have a medium sized facilty with three storage buildings. Two of them are roughly 250' away and the other is about 500' away. All I have to do in those three buildings is to monitor the status of...
  20. Replies
    2
    Views
    373

    Lon Gas Detection Devices

    Need for CO and NO2. Was planning on using a Honeywell XIO-8AI with the E3 Point sensors, but realized that definitely was not going to work. Any suggestions for sensors that can reside directly on...
  21. Replies
    2
    Views
    409

    I must be a slow learner.... I see the enum...

    I must be a slow learner....

    I see the enum proxy points but still have no idea how to switch over "the measured variable". I've tried action & set, but still shows resistance when I select...
  22. Replies
    5
    Views
    1,419

    Sounds like it came from the site "e-mails from...

    Sounds like it came from the site "e-mails from an a__hole" or something like that. Funny stuff.
  23. Replies
    0
    Views
    352

    Spyder Graphics

    Relatively new, so be kind.

    I have a simple lead/lag sequence in the programming. Created a PX view. I can simulate the programming by forcing values, but can't seem to get the PX to respond. ...
  24. Replies
    11
    Views
    1,040

    Never had to worry about that around here.... ...

    Never had to worry about that around here....

    What about using OAT & OAH sensors to determine if it is snowing?

    Is this what you currently have? http://www.networketi.com/19036.htm
  25. Replies
    9
    Views
    1,352

    Keep in mind Honeywell is not signing anyone new...

    Keep in mind Honeywell is not signing anyone new up for the R2 level as it will be obsolete in a couple years.
Results 1 to 25 of 79
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event