Search Results - HVAC-Talk: Heating, Air & Refrigeration Discussion

Search:

Type: Posts; User: dzenzel

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    875
    Views
    95,230

    jongig, I've been reading this thread. I...

    jongig,


    I've been reading this thread. I live about 100 miles southeast of you and just installed three climatemaster systems for my home. Last night, they worked incredibly well (yes, at 0F-5F...
  2. Replies
    12
    Views
    1,710

    Thank you. This was very informative. Not...

    Thank you. This was very informative.

    Not sure I need to mess with my CPH settings (3,3,9) at the moment. I was noticing run times around 15 min on 5 min off with Outside Temp in the 20s. I think...
  3. Replies
    12
    Views
    1,710

    Beenthere - CPH explaination?

    Beenthere, I believe you had earlier posted a good description of how CPH settings effect cycling of systems. I can't find the post, and am trying to understand if changing 1-stage, 2-stage, aux cph...
  4. Replies
    2
    Views
    471

    VisionPro TH8321 bad?

    Can anyone tell me if this might indicate a bad thermostat?

    Normally when the TH8321 calls for heat, there are two distinct clicks that it makes. When the heat call ends, there is a single...
  5. Replies
    875
    Views
    95,230

    Attached is an example from one of my sets. I...

    Attached is an example from one of my sets. I have a Climatemaster 5-ton packaged unit connected to three wells at 300 ft (900 ft total). The manifold is under ground and in a reverse-return...
  6. This may be off-limits, but can you tell me what...

    This may be off-limits, but can you tell me what a going rate for this type of service would be? and what would the service contain? design? design review? on-site debug?
  7. I have to agree. Not sure where the savings...

    I have to agree. Not sure where the savings are/will-be, and yes, training and knowledge/experience do account for overrun.

    I guess I had made some assumptions about the amount I could learn on...
  8. Overall, OK. Its a long story, and now time will...

    Overall, OK. Its a long story, and now time will tell if everything was worth it. I faced so much anti-homeowner sentiment and arrogance by everyone that it made the whole thing an anti-climax, after...
  9. thank you, and thanks to RoboTech, for the...

    thank you,

    and thanks to RoboTech, for the updated Goodman supplimental document. The solution to the question / issue we had was really just a close look at the low-voltage wiring (one at a...
  10. Which Goodman Airhandler config do I have?

    Please help me with this one.

    Our configuration:
    1) Compressor: Climatemaster TTS026 split unit
    1) Goodman/Amana air handler. It is an AEPF303616.
    1) VisionPro 8321U1006 thermostat.
    1)...
  11. Replies
    21
    Views
    2,067

    I have no intention of hijacking a thread, but to...

    I have no intention of hijacking a thread, but to be honest, things like this are difficult. I have a VisionPro TH8321 and there is not a single word in the installer or user manual about how stage...
  12. Climatemaster install - please don't laugh

    I'm sure not!

    Some of you may have read my previous threads with questions about loops and hardware.....well, we got through most of that, but we now face the "install". I selected an HVAC vendor...
  13. Oh well, I guess paranoia still exists on my...

    Oh well, I guess paranoia still exists on my side.

    Just found in documentation that the E code for ECM fan is only valid on the Genesis models, and that the C code is correct for the Packaged...
  14. ClimateMaster unit ID help? Is this a problem?

    My HVAC guy ordered a model number: TTV064*GE01JLKS with AGL15A
    TT = Tranquility 27 two stage R410-A
    V = Vertical
    064 = 064 MBtuh
    * = Revision Level *
    G - Voltage 208-230/60/1...
  15. Replies
    17
    Views
    1,447

    about 40- miles North of Philadelphia....

    about 40- miles North of Philadelphia....
  16. Replies
    17
    Views
    1,447

    In our house, we had a similar issue with a York...

    In our house, we had a similar issue with a York 5-ton unit and two 2.5-ton units. There was almost 90 feet of run-length from our breakerbox (400 amp) over to the compressor(s). We had PPL Utilities...
  17. Replies
    25
    Views
    1,747

    Yes, each well is 20ft apart in a triangular...

    Yes, each well is 20ft apart in a triangular formation with "box"/manifold in center with a ditch back to the house of about 30ft (30ft from manifold to house). It appeared like the manifold is...
  18. Replies
    25
    Views
    1,747

    They just finished a set of loops for me, and the...

    They just finished a set of loops for me, and the attahed picture shows the manifold that was used to connect 3 sets of boreholes (300ft deep each) for one of our systems (a 5-ton one). In the...
  19. Replies
    15
    Views
    3,122

    You gain customers by the way you treat your leads

    I've been frequenting this forum for information as I go through what I consider a large home project, that has (and continues to be) expensive and frustrating.

    I have a rather extensive...
  20. geothermal manifold - What should one look like?

    I did bring this up before, but I've been at odds with our contractor about our entire setup and this piece, I seem to be in a loosing battle on.....

    We have three separate loops
    a 5-ton...
  21. Replies
    13
    Views
    1,538

    Oh, yes... I understood the "educate yourself"...

    Oh, yes... I understood the "educate yourself" thing.... I am ordering the books (as a start)...... but that's late and short at this point, so I still need experts like yourselves to throw in some...
  22. Replies
    13
    Views
    1,538

    OK, well said, and today, I did end up speaking...

    OK, well said, and today, I did end up speaking with, and apologizing to the driller.

    Here is the real scoop. Me (HO and yes, project owner).... saw the markings and had to do some research.......
  23. Replies
    13
    Views
    1,538

    Sad part is, that while I understand the position...

    Sad part is, that while I understand the position of contractors that get bugged too much by a HO, I also as a HO feel very awkward having to even ask the question(s)! There has to be a middle of the...
  24. Replies
    13
    Views
    1,538

    Our Well Driller is listed as an IGSHPA...

    Our Well Driller is listed as an IGSHPA contractor/dealer. What I should expect when the well was drilled, was what I questioned.....It was inconsistent to see the pipe markings for the most part...
  25. Replies
    13
    Views
    1,538

    thanks. I'll talk to him when they arrive Monday...

    thanks. I'll talk to him when they arrive Monday to finish the other wells. I'm clearly over-worried that the slightest thing will throw this whole project out of whack!
Results 1 to 25 of 47
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event