Search:

Type: Posts; User: tranger03

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    287

    Hoshizaki makes an automatic ice maker/bagger...

    Hoshizaki makes an automatic ice maker/bagger setup. Might be worth looking into. Around here most of the small stores depend on delivery from the regional ice house. The ice houses here provide...
  2. Replies
    43
    Views
    1,845

    If only add that it might help if you looked at...

    If only add that it might help if you looked at the compressor as a compressor and a vapor pump. Maybe this would help you to wrap your mind around a little easier.
  3. Replies
    43
    Views
    1,845

    ^^^^ Ding, Ding, Ding

    ^^^^ Ding, Ding, Ding
  4. Replies
    7
    Views
    348

    Yes that would be my recommendation. Analysis is...

    Yes that would be my recommendation. Analysis is relatively cheap. It's just like any other preventive maintenance tool. The more frequently you sample, the clearer the readings become.
  5. Replies
    7
    Views
    348

    I like to alternate oil analysis with oil changes...

    I like to alternate oil analysis with oil changes annually. Basically, I try to do oil change annually and then at the 6 month mark I do an oil analysis reading. Not just for acid, it keeps a...
  6. Replies
    34
    Views
    1,215

    If the condenser is dirty or condenser fan is out...

    If the condenser is dirty or condenser fan is out it will cause high discharge, in turn causing high suction. I would start there before I condemned the compressor.
  7. Replies
    30
    Views
    1,387

    That's very interesting. Who knew shaft seals...

    That's very interesting. Who knew shaft seals could lead to good conversation. I work mostly with Vilter 440/450 compressors. This is the actual language from their service manual. 471231
  8. Replies
    8
    Views
    490

    www.omega.com If you have time to order it...

    www.omega.com
    If you have time to order it they'll have what you need.
  9. Replies
    30
    Views
    1,387

    Not sure what the instructor was referring to in...

    Not sure what the instructor was referring to in this case. In order for the shaft seal to perform properly the bellows need to be constantly lubricated. There is a weep/drip hole in the bottom of...
  10. Replies
    30
    Views
    1,387

    100% agree with all the previous posts, but I...

    100% agree with all the previous posts, but I would also add that the compressor type you choose is going to be determined in large part by your system requirements and who engineers it. I have one...
  11. Replies
    1
    Views
    418

    Anyone heard of openings in the DFW area?

    Anyone heard of openings in the DFW area?
  12. Replies
    1
    Views
    418

    Industrial Refrigeration DFW

    Hello all. I am trying to relocate to the DFW area and need some help finding industrial refrigeration companies in the area. I have about four years of experience working on a variety of different...
  13. Replies
    20
    Views
    1,312

    Simple green in a Hudson sprayer. Spray the...

    Simple green in a Hudson sprayer. Spray the whole coil down with the simple green. Let it soak for a few minutes. Use water hose with nozzle to wash off dirt. If you have access to warm of hot...
  14. Replies
    10
    Views
    1,272

    I'll try that. Thanks medic.

    I'll try that. Thanks medic.
  15. Replies
    10
    Views
    1,272

    Run cap is new and I have checked it multiple...

    Run cap is new and I have checked it multiple times thinking the same thing. Still shows correct capacitance (35).
  16. Replies
    10
    Views
    1,272

    Compressor pulling high amps

    Alright guys,

    Looking for a little help on a problem unit I am dealing with. First call was to replace the dual cap due to condensing fan not running. Replaced the cap, but the compressor was...
  17. Replies
    10
    Views
    1,715

    Forklift....wheels up

    385481

    Have no idea how it happened, but my customer called asking for a crane and sent me this picture. In the end they were able to get it turned over with some other forklifts. Wish I could...
  18. Thread: Body cooler

    by tranger03
    Replies
    26
    Views
    1,556

    Suddenly the hotter than hell process plant in...

    Suddenly the hotter than hell process plant in working in doesn't seem so bad. If they ask you to check out a problem with the inside of the oven, I suggest turning that work down.
  19. Replies
    19
    Views
    1,203

    Sorry ga hvac my post was directed at the op not...

    Sorry ga hvac my post was directed at the op not to you. We must have posted at the same time. I also was trying to provoke the op to think where the moisture would have come from that they thought...
  20. Others have said it but it doesn't seem like they...

    Others have said it but it doesn't seem like they were heard. Before you do anything else you need to clear the sight glass and set the superheat for each txv, not just if it is "flowing" or not. ...
  21. Without knowing the amp draw on the motor it's...

    Without knowing the amp draw on the motor it's going to be hard to say what's wrong with your motor. My advise would be to triple check that all of your connections are torqued properly.
  22. Replies
    19
    Views
    1,203

    That sounds like a wonderful textbook answer, but...

    That sounds like a wonderful textbook answer, but where did the moisture come from???
  23. Thread: Hose seal

    by tranger03
    Replies
    10
    Views
    751

    JB makes enviro safe hoses

    JB makes enviro safe hoses
  24. Replies
    9
    Views
    1,775

    Reminds me of techs who turn ball valves past the...

    Reminds me of techs who turn ball valves past the stop pins and shear them off. If something takes that much force I try to make a habit of taking a second look at the situation before proceeding. ...
  25. Replies
    77
    Views
    8,496

    On call is a mind set. We're on call from Monday...

    On call is a mind set. We're on call from Monday to Monday about once a month. During that week I just get it in my mind that I'm going to get called out. That way when I do it's not such a big...
Results 1 to 25 of 69
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event