Search:

Type: Posts; User: jrbenny

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    6
    Views
    269

    It will work. Need to use a 1" wrap.

    It will work. Need to use a 1" wrap.
  2. Replies
    22
    Views
    804

    Daikin allows two of three/four heads to be...

    Daikin allows two of three/four heads to be installed. All ports are not required to be connected.
  3. Replies
    26
    Views
    1,091

    Only has ten years if registered within sixty...

    Only has ten years if registered within sixty days of installation.
  4. Replies
    28
    Views
    1,322

    You're welcome.

    You're welcome.
  5. Replies
    28
    Views
    1,322

    Court is fun. You can get paid quite well as an...

    Court is fun. You can get paid quite well as an expert witness.

    To each their own.
  6. Replies
    28
    Views
    1,322

    Well, sounds like you walked away from a nice...

    Well, sounds like you walked away from a nice payday. You've likely come across a curb adapter that is too short. See it all the time from value engineered adapters. A 10-ton unit needs a 18-22"...
  7. Replies
    7
    Views
    297

    Also, no rotary in the gsx14. They're all...

    Also, no rotary in the gsx14. They're all Copeland scroll.
  8. Replies
    7
    Views
    297

    Change to the 5mm coils.

    Change to the 5mm coils.
  9. Replies
    7
    Views
    297

    Not really. It's in the 018-C and 018-D that can...

    Not really. It's in the 018-C and 018-D that can see in the parts manual. Personally, I think they will use fewer Copeland over the coming years. Their parent company makes great compressors.
  10. Replies
    7
    Views
    297

    They're putting rotary in some of the smaller...

    They're putting rotary in some of the smaller sizes.
  11. Sticky: No

    No
  12. Replies
    17
    Views
    585

    How long are the linesets? What's the change in...

    How long are the linesets? What's the change in elevation? What are the lineset sizes? Did you makes sure all the oil was removed from the linesets?

    BL is right about short on airflow as well.
  13. Replies
    3
    Views
    260

    Gas valve.

    Gas valve.
  14. Sticky: When will your tech reps be given access to the...

    When will your tech reps be given access to the private jet? :)
  15. Replies
    12
    Views
    927

    Close on rise temperature switch could be wired...

    Close on rise temperature switch could be wired too. Energize a relay that bypasses the Y circuit and jumps the W. NC contacts would connect thermostat Y to outdoor Y. NO contacts would connect...
  16. Replies
    12
    Views
    927

    Tell Granny to flip it to emergency heat when...

    Tell Granny to flip it to emergency heat when it's above 65f outdoors.
  17. Replies
    17
    Views
    1,185

    Underside of compressor connections and true...

    Underside of compressor connections and true suction tap are where I've seen them.
  18. Replies
    26
    Views
    1,571

    Say what? Are you saying that you don't know...

    Say what? Are you saying that you don't know where you called to order a compressor? What distributor did you call?
  19. Replies
    26
    Views
    1,571

    Who's your supplier?

    Who's your supplier?
  20. Replies
    9
    Views
    654

    Dancing girls and free beer.

    Dancing girls and free beer.
  21. Replies
    5
    Views
    464

    Class B is the amount of time. Your labor dollar...

    Class B is the amount of time. Your labor dollar amount is registered with Goodman if you're in the Asure program. If not in Asure, it's $xxxx an hour.

    I don't have the rate schedule handy. ...
  22. Replies
    24
    Views
    1,177

    It's attached to post #7 here. Can't you see it?

    It's attached to post #7 here. Can't you see it?
  23. Replies
    24
    Views
    1,177

    Read the service bulletin.

    Read the service bulletin.
  24. Replies
    24
    Views
    1,177

    Have a look at this. :cheers:

    Have a look at this. :cheers:
  25. Replies
    7
    Views
    420

    How about you size for heating and let the...

    How about you size for heating and let the compressor idle back in cooling?
  26. Replies
    7
    Views
    626

    Been using one since 2006. Same one. Cal check...

    Been using one since 2006. Same one. Cal check frequently. Works like a champ.
  27. Replies
    87
    Views
    13,853

    Not without voiding the warranty.

    Not without voiding the warranty.
  28. Replies
    9
    Views
    380

    Daikin is a solid unit. Balconies and Lute Supply...

    Daikin is a solid unit. Balconies and Lute Supply gave you the correct warranty information.
  29. Replies
    62
    Views
    2,397

    The "breaker" on the heat kit is a disconnect...

    The "breaker" on the heat kit is a disconnect contained within the unit. It does not fall under the NEC requirements as does the breaker in the panel. 45A breaker goes in the panel. It's not a typo....
  30. Replies
    5
    Views
    451

    I love these threads. :)

    I love these threads. :)
  31. Replies
    58
    Views
    2,592

    Mods. Please move this to ARP.

    Mods. Please move this to ARP.
  32. Replies
    58
    Views
    2,592

    [emoji12]

    [emoji12]
  33. Replies
    87
    Views
    13,853

    If I did it again, I'd start in an extended cab...

    If I did it again, I'd start in an extended cab pickup with a topper and side access boxes. Pull a trailer for installs.
  34. Your pad sizing should just say three inch...

    Your pad sizing should just say three inch overhang on each side rather than 36" square. What if the unit is 37" square?

    GFCI should be 120V. :)
  35. Air handler ships on low speed. Highly doubt...

    Air handler ships on low speed. Highly doubt your friend changed the speed.
  36. Replies
    21
    Views
    3,705

    I don't do stuff there. That's jellystone...

    I don't do stuff there. That's jellystone territory.
  37. Replies
    21
    Views
    3,705

    I know a good trainer that does classes in...

    I know a good trainer that does classes in Dayton. :-)
  38. Replies
    8
    Views
    693

    Should be less than 2vac for any and all furnace...

    Should be less than 2vac for any and all furnace control boards.
  39. Replies
    44
    Views
    2,965

    Ten year parts warranties. Making a killing on...

    Ten year parts warranties. Making a killing on HSI. :playing:
  40. Replies
    44
    Views
    2,965

    Yes, Glenn, I do. As an OEM technical rep, I well...

    Yes, Glenn, I do. As an OEM technical rep, I well aware of the decisions made when considering furnace design. You can disagree all you want but that doesn't make you right. ;)

    I'm out.
    ...
  41. Replies
    44
    Views
    2,965

    Spark is louder than a hot surface ignitor. Thus,...

    Spark is louder than a hot surface ignitor. Thus, HSI is the primary use for residential gas furnaces in current production for most OEM.
  42. Replies
    7
    Views
    558

    Defrost will last up to ten minutes while there's...

    Defrost will last up to ten minutes while there's a call for heat. How long did you let it run? I seriously doubt you have a control issue.
  43. I question where you are measuring your static...

    I question where you are measuring your static pressure. Goodman fan coils are good to 0.8 IWC full capacity and lose 3% airflow for every 0.1 IWC just LIKE EVERY OTHER OEM.
  44. Thread: 5 ton daikin

    by jrbenny
    Replies
    5
    Views
    589

    Is that an AHRI match? Did you verify on AHRI...

    Is that an AHRI match? Did you verify on AHRI site? How do you know you're moving 1975 CFM?
  45. Replies
    44
    Views
    2,965

    Primarily, it's not done in a gas furnace any...

    Primarily, it's not done in a gas furnace any longer because of noise.
  46. Replies
    0
    Views
    849

    Veto Pro Pac LT-XL

    I'm selling my Veto Pro Pac LT-XL. I just don't need it as a trainer and tech rep. Great bag for controls and rooftop work if you carry a laptop. Retail price is $250 for the current model. All...
  47. Let's hope there's a happy ending. :eek:

    Let's hope there's a happy ending. :eek:
  48. Email sent to Adam with the OP contact...

    Email sent to Adam with the OP contact information. ;)
  49. Truth always lies somewhere in the middle.

    Truth always lies somewhere in the middle.
  50. If you'll send me an email, I will help you get...

    If you'll send me an email, I will help you get this resolved. I'm really surprised the CA rep gave you the run around.
Results 1 to 50 of 1000
Page 1 of 20 1 2 3 4

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Quality Home Comfort Awards