Search:

Type: Posts; User: eswells95

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    32
    Views
    6,048

    Thanks for all your replies and advice.

    Thanks for all your replies and advice.
  2. Replies
    32
    Views
    6,048

    What is a filter dryer, it's purpose, and where...

    What is a filter dryer, it's purpose, and where would it have been used/replaced?

    Should I assume that the leak was there since the initial install in May? It was at a joint in the liquid line...
  3. Replies
    32
    Views
    6,048

    Thanks everyone. I didn't notice which way the...

    Thanks everyone.

    I didn't notice which way the tank was standing when he did the recharge. I feel pretty certain that there wasn't a micron gage based on what he showed me and my 20 minute...
  4. Replies
    32
    Views
    6,048

    Thanks for all your responses. I've had...

    Thanks for all your responses.

    I've had several problems since my install in May. The technician called me over to see the gage. I didn't see any units of microns. I had read on here about...
  5. Replies
    32
    Views
    6,048

    Fixing Refrigerant Leak on Trane Heat Pump

    I had a service tech out to find and fix a suspected refrigerant leak on my new Trane XL16i heat pump that was installed in May 2007. As I've had some problems with my install, I wanted to see if...
  6. Replies
    19
    Views
    1,567

    Thanks Second Opinion. The service tech is...

    Thanks Second Opinion.

    The service tech is here now and hasn't found the refrigerant leak yet. Is there any problems doing this fix in colder weather (low to mid 30's)?
  7. Replies
    19
    Views
    1,567

    Thanks everyone. Second Opinion: I was pretty...

    Thanks everyone.

    Second Opinion:
    I was pretty sure I knew how you felt about my installer :) Thank for all your great advice.

    Although it looks essentially the same as Fig #11, isn't the...
  8. Replies
    19
    Views
    1,567

    Thanks for all your responses. 2nd op, can...

    Thanks for all your responses.

    2nd op, can you tell us how you really feel about my dealer? Don't hold back.

    Even if his comments were clueless, I'm still not sure how my installer setup the...
  9. Replies
    19
    Views
    1,567

    HP Defrost operation w/Dual Fuel system

    In several posts here I've seen that during a Heat Pump defrost cycle, the supplemental heat generally gets a call from the heat pump. This seems definitely to be the case when the supplemental heat...
  10. Replies
    15
    Views
    1,726

    Wormy, thanks a bunch for your responses. You...

    Wormy, thanks a bunch for your responses. You are correct that these systems can be confusing to a homeowner. I'm interested in understanding my system on a general level but would be happy enough...
  11. Replies
    15
    Views
    1,726

    Thanks for all the great info. I'm measuring...

    Thanks for all the great info.

    I'm measuring the temps consistently in the plenum before and just beyond the furnace so I feel pretty sure that the measurements are not the problem. The return...
  12. Replies
    15
    Views
    1,726

    This isn't HP operation. It's aux/gas heating in...

    This isn't HP operation. It's aux/gas heating in my dual fuel setup.

    markf57: I haven't upgraded to the IAQ. I wasn't sure if I wanted to introduce another variable into the problems I've...
  13. Replies
    15
    Views
    1,726

    Can anyone explain this furnace behavior?

    In May 2007, I had the following system installed:

    XL16i Heat Pump 4TWX6036B1000AA
    XV80 100k TUD100R9V3K
    TCONT803 tstat w/Outdoor temp sensor

    I've received alot of great advice and answers...
  14. Replies
    13
    Views
    1,820

    Thanks for all the advice. I wiped off the...

    Thanks for all the advice. I wiped off the liquid line, to remove any soapy lubricant that may still reside on the line after the initial install. A few hours later, I felt under the joint of the...
  15. Replies
    13
    Views
    1,820

    My installer called me back today. He seems to...

    My installer called me back today. He seems to think what I'm seeing is some soapy lubricant they use during install to make it easy for things to slide over the tubing and to check for leaks at...
  16. Replies
    13
    Views
    1,820

    Thanks everyone. Will they need to check the...

    Thanks everyone.

    Will they need to check the level of the refrigerant and "pull a vaccuum" again when they come out to fix the leak? Is doing that a problem in colder temps? Is there anything I...
  17. Replies
    13
    Views
    1,820

    It seems like an oily liquid.

    It seems like an oily liquid.
  18. Replies
    13
    Views
    1,820

    Problem with liquid line leaking/dripping

    I have a Trane XL16 Heat Pump dual fuel setup with a Trane XV80 gas furnace that was installed this past May.

    I just noticed a small drip from the small copper tube (liquid line?) that enters...
  19. Replies
    57
    Views
    4,652

    Mark57 indicated he was running his heat pump...

    Mark57 indicated he was running his heat pump down to 15 degrees.
  20. Replies
    11
    Views
    4,626

    Thanks Mark. That's what's in the schematic...

    Thanks Mark.

    That's what's in the schematic (TCONT803 install instructions) that I think my installer used to setup my system (X2 on T-stat to W2 on furnace).

    Is that the correct setup? ...
  21. Replies
    11
    Views
    4,626

    Thanks Second Opinion. I'm still trying to...

    Thanks Second Opinion. I'm still trying to understand how I'm getting to 2nd Stage in Emergency Heat after 10 minutes, but not in Regular Heat Mode. Any help is appreciated.

    My e-mail is in my...
  22. Replies
    20
    Views
    5,177

    I think Tecman may be right. I have a TCONT803...

    I think Tecman may be right. I have a TCONT803 (which I think is a re-branded 8321 or close).

    In my case I have a dual fuel setup with aux/gas heat. The t-stat is set to lockout the compressor...
  23. Replies
    11
    Views
    4,626

    No DIY here

    I'm probably about as far from a DIY candidate as you can find on this forum. In any case, I won't be touching any wiring.

    I am trying to find out if I have a problem (pretty sure that...
  24. Replies
    10
    Views
    1,280

    Thanks for the comments. Was the chimney kit...

    Thanks for the comments.

    Was the chimney kit a bad option for me?

    I wasn't thrilled when I saw the end product of the AA 2200 filter install. My contractor tried to assure me that the...
  25. Replies
    10
    Views
    1,280

    pics of wiring/setup in a different thread (URL)

    The pics of my wiring/setup are in another thread:

    http://hvac-talk.com/vbb/showthread.php?t=155911

    Thanks for your help.
Results 1 to 25 of 43
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event