Search:

Type: Posts; User: swinginutters

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    1,037

    Turbo Air compressor replacement?

    Need a compressor for a turbo air freezer TSF23SD. The compressor is a tecumseh but made in france CAE2420Z. Its a 1/2 horse 404, i think rated at about 2000 btu at -10Fevap. I was thinking...
  2. defrost limit vs. defrost termination

    hobart reach in freezer daf-2, has a factory defrost limit bimetal that cuts off the heaters but still has to time out on defrost. They had it set to 4x's a day at 40 minutes each which seemed...
  3. Replies
    4
    Views
    566

    any body know the number for hobart tech support?

    any body know the number for hobart tech support?
  4. Replies
    4
    Views
    566

    hobart cap tube size

    need cap tube size and length for a hobart mod #DAF 2b 404, according to the supco chart for a 3/4 comp I need two lengths of #1(.081 OD) at
    39 inches each. Has anyone used this chart...
  5. Replies
    4
    Views
    750

    went to one web site and they showed it as 1 hp...

    went to one web site and they showed it as 1 hp 134-a, and another web site and it's a 3/4 404,

    So it is a 404 3/4 horse
  6. Replies
    4
    Views
    750

    Hobart hack mess please help

    Took over an acount a while back they call and have a reach in Freezer warm Mod# DAF2 hobart. They said the last guy just put in a new comp about 6 months ago. The problem is the tag says 404, 21...
  7. well said, thanks for the input. It's hard...

    well said, thanks for the input. It's hard when everybody is crying about money now and nobaby wants to spend to do it right. But you end up shooting yourself in the foot if you give them...
  8. yes it did have pressure built up inside the cap,...

    yes it did have pressure built up inside the cap, it actually poped pretty good when taking the cap off. The Cpr was pretty loose when adjusting it too. I did adjust it by amp probe under the rated...
  9. masterbuilt blast freezer CPR valve question

    master built blast freezer IHC-48erc2


    compressor struggling to start copeland katb015ecav230 was doing the chugga chugga for about 10 seconds than cut out on overlaod. check start components, ...
  10. Replies
    5
    Views
    698

    i figured, so besides re doing the whole drain...

    i figured, so besides re doing the whole drain line heater 220 volt, which I'd rather not do since the run is pretty long with tons of stuff in the way. what would be a safe alternative to suggest...
  11. Replies
    5
    Views
    698

    nuetral wire to ground??

    In a walk in freezer today saw a 120 v drain line heater with the nuetral wire to ground, we have all seen this style stuff at times, but jsut wondering does it pose any saftey issues for any real...
  12. Replies
    5
    Views
    1,563

    got it!!!!

    Thank you for the help , god bless the internet, after looking at the manual it all made sense, all three elements are wired in series on stand by mode, it pulls 5 amps, then on constant or when...
  13. Replies
    5
    Views
    1,563

    Lang cheesemelter over amping ??????

    i"m a refrigeration guy working on a cheesemelter. This thing is wired to a 208 v 15 amp beraker, which seemed really small to me. Model #mm36 it was only running off of the front two elements...
  14. Replies
    5
    Views
    624

    pumping down

    when pumping down a walk in cond unit with king valves to evacuate it for say a txv repair or something in the line set. my question is regaurding the suction king valve. If you front seat it, your...
  15. words of wisdom , it is pretty rusty, thanks for...

    words of wisdom , it is pretty rusty, thanks for the info,
  16. possible to repair a steel cond coil?

    i have a leak at the botton of a steel cond coil AEA3425yxaxa pretty bad spot not very easy to get to.

    first question, is it possible to repair these with mixed metal solder or something else? ...
  17. Replies
    4
    Views
    802

    if you go to the hoshi website and look at FAQ...

    if you go to the hoshi website and look at FAQ they have a article clearly explaining how many beeps means what. excess freeze time, excess harvest time or what ever, and you can download the...
  18. Sizing an unknown air handler for a walk in chill

    I'm replacing an airhandler on a walk in chill for a friend. It's old and crusty and has no numbers, so i got the cond unit # and I think I found a correct fit, but if you guys could look this over...
  19. Replies
    4
    Views
    606

    it has a digatal stat too, up and down arrows ...

    it has a digatal stat too, up and down arrows and levels 1 through ten on the dispaly cold to colder
  20. Replies
    4
    Views
    606

    turbo air TSR-23sd 2 temp controls?

    working on a turbo air TSR-23SD single door cooler , from what i can tell nobody likes these things. but i see it has it's digital display for temp control and a standard mechanical dail one...
  21. Replies
    5
    Views
    640

    yeah that makes sense, i did notice that the...

    yeah that makes sense, i did notice that the nickel was worn out a bit, but it looked the same on all the evaps, no scaling or at least it didn't look like it, would it be worth putting it through...
  22. Replies
    5
    Views
    640

    crystal tips not dropping ice

    working on a crystal tips mod # 800-cws-261 runs great makes ice, but when harvest hits the side evaps drop ice well the middle evaps like to hang on to the ice, sometimes not dropping the ice adn...
  23. Replies
    2
    Views
    577

    True TSID 48-4 temp control?

    On a True TSID 48-4 deli case, I need to replace the temp control, with a ranco, but don't know the range, this model has no evap fan, which i thought was a goofy design but after reading i guess...
  24. Replies
    8
    Views
    948

    thanks for the info, i didn't have time to dig...

    thanks for the info, i didn't have time to dig into it more i had to get outta there. But I remember one time my old employer was talking about a steel coil in as randell prep top that we...
  25. Replies
    8
    Views
    948

    traulson evap coils

    ran into a traulson reach in mod # RHT23NREFSL with a hole in the evap turn right side. The temp control wire rubbed and ended up shorting out to the coil turn and put a hole in it. My question...
Results 1 to 25 of 55
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event