Search:

How many and what type modules do you have on the TX rail. Maybe you've gone over the power limit. The mA inputs and outputs are pretty hungry

Sorry, google translate must be playing up. I'm usually quite good at working out broken english but struggling with your reply. could you get someone to redo it to help me understand what you want...

If you're asking can you upload the software from a PXC64U or a PXC128U into XWorks if you don't have the original software then I'm afraid you can't. You need to keep a working copy of the software...

I'd say for Q1. No and for Q2..... No

Have you used the batch job option? I've always been a little nervous to use it on a big site in case it screwed up. The one time I tried it on a small job it...

Has any one managed to get wireless M-Bus into a BMS system?

I've done M-Bus before but looking through google for a definitive answer on how to connect Wireless M-Bus is proving difficult. It...

Is this for a European PXC controller? If so do you have access to manual CA2Y9772en.pdf? This shows how it is engineered. A BO with address D=54 needs to be created and comInfo3 needs to be set to...

Not being too familiar with the US PXC Compacts (I use the European LON and ethernet versions) I was wondering how you are connecting to them. Is this MS/TP via a com port on your laptop? Have you a...

Can't see your email in your profile. I have the V3 SDU directory which has all the files you want. Email me and I'll send them back to you.

I wish you luck in your project. I had a similar...

Do you recon those floor plans were done using ASCII characters. Did a few graphics back in the day doing that.

What help do you need?

The common alarm block allows the acknowedgement and resetting of all alarms in the current chart and all charts below by connecting to the relevant pins to do the acknowledge or reset.

In...

You need one big DIEPT file. Its basically one file per site. You cant have seperate ones for each controller.

Could be. do they have a part number on them?

If your using a T1 sensor (FR-T1) then the table below is right. The new type of sensor you have been sent might be a Ni1000 sensor (QAA24?) which are 0°C at 1000 Ohms. You can change from old to new...

we tend to use these guys.

http://www.synapsys-solutions.com/

Seem to do a pretty good job

The TONN (basically a trend badged tridium controller) would probably take in the LON from the TAC. But I'll say that they're opening themselves up to a whole load of issues. To modify any of the TAC...

I can send you a scanned in staefa service manual that has all that kit except the R.U22 but its 12Mb. Stick your email address in your profile and I can send it later today.

OK, so updated my java to 7 (Version 6 Build 41) and all seems to work fine now. Of course some stuff not implemented but as a start pretty good. Talks fine to my delta DSC1616E controller anyway. My...

Looks like a great idea. What java version do I need as I get class version errors when I try and run

java.lang.UnsupportedClassVersionError: Bad version number in .class file

Sorry, was getting my part numbers mixed up. I stated PXC3.L but I was actually talking about a PXG3.L

The device you are talking about is part of their Total Room Automation range and I believe...

Theres a number of flavours of PXC3's, there the PXC3.L which is a BACNet/LON to BACNet/UDP/IP router, the PXC3.M which is the same as PXC3.L but with added MS/TP connections, and I think there is a...

By Schedule do you mean install/configure and that you cant find it as a device in the drop down menu?

I believe you need XWorks V5. They also have a stand alone program to set it up as well but...

sent a new link, but check your spam folder

OK, but best remove your email from the thread. Should go in your profile...

drop me an email and I'll reply with the files.

Is the tool you're using the new one or the old one? the new tool works best if the firmware files are saved in a certain file structure. Its a big...

here's a screen shot of the settings a colleage has set to get his NIC709-USB100 working with XWorks

347391

You'd need to put your email address in your profile if you want anyone to help you on this I think.

Also, have you tried contacting your local Staefa branch?

I can confirm this device does work fine. we have a few people using them in the office. you need to go into advanced settings and select legacy mode. also a good idea to run it as a service

Have you ever been able to connect with this interface to other PXC's or is this the first time you've tried it?

I think I tried one of these devices previously with XWorks 2.37 and it didn't...

I know what you mean. I installed some wireless sensors a while back as drilling the grade 1 listed building was out of the question. But the 2 foot think walls in places meant reception was an...

Has anyone connected wireless MBus devices to a BMS? I have a solution for wired MBus but struggling a bit with wireless.

What devices have you used to convert it into a protocol that your BMS can...

That would be a great application. Not sure about setting the standard weekly schedule through it but I could see exceptions and calander events being integrated quite well.

I use this:

http://www.blackbox.co.uk/gb-uk/sp/45256/USB-Powered-Ultra-Compact-Ethernet-Switch

Its not a hub which is a shame, but as it can be powered by your USB port its really useful where...

What data are you looking for?

They have an add on called report generator that generates reports and exports as excel or pdf;

They do a package called ADP (Advanced Data Processing) if you...

To check for interference you will need something like an oscilloscope or a protocol analyzer. I must admit I'm no expert on this so maybe read some of the other threads on this site. (Do a search...

You really need an RXZ01.1 if using a star topology. Try this first. If you want to use RXZ02.1's you need one at each end of the network. I'm sure you can make a bus topology network the way you...

I suppose I was just looking for something basic, flagging up an alarm has occured and at what time. What I was thinking of was that Siemens Europe have a device called a PXM20 (a hand held device)...

The thing I've always wanted was for some clever chap to make an alarm receiver widget. A building manager could then just have this installed on his PC and any alarms could then be sent direct to...

Well they call it a modbus explorer but not sure it's as feature rich as the bacnet one

http://www.chipkin.com/technical-resources

Chipkin do a modbus "explorer" but I havent used it yet. Maybe worth a try. They have a few other bits of software that's quite useful like an Rtu parser as well.

Have you tried their web site?

http://www.multitek-ltd.com/

Sorry, I miss read the post as was reading on my phone.

I'll try and post again

https://hit.sbt.siemens.com/HIT/fs_global.aspx?RC=AA&lang=en&MODULE=Catalog&ACTION=ShowProduct&KEY=BPZ:GEB..1E&TITLE=Rotary+air+damper+actuators+15+Nm%2c+without+spring+return

The error looks familiar but can't think what it definatly is. Was the project upgraded from a 2.37 project. I sometimes find the upgrade process is not always perfect and old version blocks are left...

Sed2's are not my specialty. I'd recommend you start a new thread on the forum and ask the other guys on here

The reason I asked what firmware version for 2.37 was I heard that new PXC's were coming out with new chips in them that were not compatible with the 420 firmware.

I received a bulletin last...

What firmware did you download to it? is it V4 or downgraded to V2.37?

did you use PXC_CMP12-22 V2.20.424.dwz or PXC_CMP12-22 V2.20.420.dwz if downgraded?

Can you confirm that the correct buttons are being pressed

http://www.big-eu.org/catalog/siemens/023_PXC..D_CM1N9215en_08.pdf

Have a look on page 7.

Also check that the AA battery is healthy...

Looks like your controller might be faulty. There are some commands that can be used on the controller while using the firmware download tool if its in "Coma" mode but I don't have the documentation...

Seems an interesting problem.

The only thing I ever had close to this was when I needed to do some work on a PXC00-U doing RXL's. I tried downloading the firmware but it wouldn't take the download...