Search:

Type: Posts; User: itsamine

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Power outage

    by itsamine
    Replies
    19
    Views
    844

    Next time that happens boil a big pot of water to...

    Next time that happens boil a big pot of water to put some humidity in the air.
  2. Replies
    35
    Views
    1,514

    X2

    X2
  3. Replies
    27
    Views
    2,454

    X2

    X2
  4. Replies
    14
    Views
    2,893

    After it fills with water close the isolation...

    After it fills with water close the isolation valve for the water inlet(before the solenoid valve) and see what happens. It might be leaking by. When you unplugged the FS did it go into harvest? I do...
  5. Replies
    61
    Views
    3,715

    I have and use the TIF-ZX1 and it works very well...

    I have and use the TIF-ZX1 and it works very well for me. I have found some very small leaks with it. On walk-ins all I do is just open the door enough to stick the sensor in there and if there is a...
  6. Replies
    5
    Views
    1,985

    Depends on the air temp.

    Depends on the air temp.
  7. Replies
    10
    Views
    1,680

    X2

    X2
  8. Do you have anything in the utlilty room that is...

    Do you have anything in the utlilty room that is being pulled into the return? Bleach or other chemicals? Does it smell like your utility room?
  9. Replies
    42
    Views
    2,866

    Yep just had one like that.

    Yep just had one like that.
  10. Replies
    13
    Views
    1,127

    One easy way to check sight glass if unsure is...

    One easy way to check sight glass if unsure is just pump it down.
  11. Replies
    10
    Views
    3,845

    Did you look at the expansion vlv to see what...

    Did you look at the expansion vlv to see what kind of gas or run the compressor numbers by the supply house to see what it is? R409a you can drop right in an R12 rated system with out major changes....
  12. Replies
    7
    Views
    695

    Frosty Factory is ok also... ...

    Frosty Factory is ok also... http://www.frostyfactory.com/products.php
  13. Replies
    12
    Views
    3,600

    When in doubt change it out. I always replace the...

    When in doubt change it out. I always replace the LL drier when I open a system up.
  14. Thread: TXV Cloging

    by itsamine
    Replies
    23
    Views
    1,937

    The heat inside a kitchen (where most condensers...

    The heat inside a kitchen (where most condensers are located) will do more damage then brazing without nitrogen will ever do.
  15. Thread: TXV Cloging

    by itsamine
    Replies
    23
    Views
    1,937

    Filter not builder... damn driod.:whistle:

    Filter not builder... damn driod.:whistle:
  16. Replies
    7
    Views
    653

    Break cleaner.

    Break cleaner.
  17. Thread: TXV Cloging

    by itsamine
    Replies
    23
    Views
    1,937

    [QUOTE=VTP99;10231362] That's a100% proof it's...

    That's a100% proof it's from not using nitrogen. If that's the case wouldn't you see the screen clog alot faster?
  18. Thread: TXV Cloging

    by itsamine
    Replies
    23
    Views
    1,937

    It's more of the builder breaking down than...

    It's more of the builder breaking down than anything else.
  19. Thread: TXV Cloging

    by itsamine
    Replies
    23
    Views
    1,937

    Welp let it begin... I have never seen it or read...

    Welp let it begin... I have never seen it or read any documentation about this happening when nitrogen is not used. Please by all means show me the proof not the "theory" it could be. I would love to...
  20. Replies
    9
    Views
    2,321

    Sounds like an air leak but I would also check...

    Sounds like an air leak but I would also check the fan delay.
  21. Replies
    49
    Views
    3,274

    X2

    X2
  22. Replies
    11
    Views
    997

    No.

    No.
  23. Thread: E2 problem

    by itsamine
    Replies
    14
    Views
    1,066

    E2 is memory loss. Needs a new one.

    E2 is memory loss. Needs a new one.
  24. Replies
    9
    Views
    901

    It's from the water. The machine needs to be...

    It's from the water. The machine needs to be cleaned more often.
  25. Replies
    31
    Views
    2,196

    By no means I saying this is what happening but I...

    By no means I saying this is what happening but I has seen moisture reak havoc on systems. I have seen where it will form a ball of ice in the txv and screw evrything up. Then after awhile it melts...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event