Don't know about batteries, but I have an ammeter that I have problems
with when taking it from the cold van to a warm house or if working outside
in rain or snow. Believe it is moisture...
Type: Posts; User: twosticks
Don't know about batteries, but I have an ammeter that I have problems
with when taking it from the cold van to a warm house or if working outside
in rain or snow. Believe it is moisture...
Hot Shot is a replacement for R-12. Can't use for R-502.
All of your readings are on the lo side indicating a lo load. You mentioned ice on coil and
suction line. You may have been still iced up. You have to look at both sides to verify
that it is...
User Interface.
Ploease don't give DIY here.
Oops, I knew that. Don't know what I was thinking. Guess I wasn't.
Aren't Goodman RV's energized in heat mode? If the RV is stuck, shouldn't he be getting
conditioned air in either mode, just not the condition he wants? Is the heat he is getting
coming from...
We install Carriers which are made by Climatemaster so I am going to assume some
things to be the same, but they may not be. If your water loop is what is called an open
loop,the unit may be...
Don't know what manufacturers pressurize to nor why. The lo side on a heat pump
becomes the high side and sees working pressures higher than that, 410a substatially
higher. A/C only,R22 ,left...
Can you tell us what his reason is or is it a secret?
Might want to make sure your stat is not set to Em. Ht. before you call. In em. ht.
mode the electric heat will run, the ht. pump won't. Kind of an obvious thing but it
sounds like you are not...
If I understand the O.P. correctly, the space temp displayed on the stat is 45 degrees.
Is that true?
Hi voltage does not have to be present at O.D. unit to display O.D. temp.
Cooling load in our area does not justify Two stage cooling only. We sell
Infinity heat pumps only. They come with O.D....
There is no heated air from the furnace, heat pump and furnace do not run
at the same time.
Don't know who "advised" you, but that is not even close to right.
Can't give you instructions, against the rules. Kinda surprised someone
sold you that control.
Nathan, remove your e-mail from your post. It's not allowed. Labor rates will
vary from region to region, even between companies in the same area.
Contact a couple of contractors in your area...
Is there a reason they can't include a wiring diagram of the switch in the package?
Wow. I was taught (by a manufacturers service rep) that all I needed was a hole in duct and insert hose or cover the hole w/ hose for static pressure.
He even demonstrated by removing a screw and...
Idaho
After registering, I lurked for a year. Got brave and wanted to post but
couldn't. Hooked up with Boss, he couldn't tell me what the problem was
(security thing I guess). Asked him if he could kick...
When Boss was running the show I got kicked off without ever posting.
Always wondered if that might be a record.:)
Don't rule out the sewer gas comment. Have had three calls for gas leaks
that were solved by pouring water into dried out open traps.
Thanks for the replies. Tag on compressor said MIN. No markings to indicate
field changes. I put 3GS in it.
Got an MRA20500TFC800 Compressor, low temp, 502. Needs a little oil.
I know it's mineral oil but don't know the viscosity. What can I use? I have
3GS and 4GS available right now.
Don't know that I have seen or heard of any spec's, But in my opinion 6'
minimum. I personally would want it further than that.
Iknow this doesn't answer yuor question, but Carrier requires 24"
between units.
I was told that when the needles on your guages are parallel you are
properly charged (by my boss). Whatever method the guy in the pic
uses, he won't be able to dial it in. He doesn't have a red...
refrtech- Thanks for the tip, but who's Southwest Airlines?
I don't remember ever seeing that username on here.
I'm in Idaho. Can I catch a ride with someone?
Well, when I went to check replies all I could view was my original post until I replied and there you were. Don't
have Firefox, am a total idiot when it comes to computers
(I only know the...
When I check out a thread and it's replies the first time
everything is fine. When other replies are added later and
I go to that thread, the additional replies are not there,
the last reply is...
Adding R-22 to a system containing less than 50# of ref.
was not in violation of any EPA regulations when I got
certified 10 years ago. I am not aware of any changes.
See alot of people make the...
Don't work with that type of furnace much, mostly 90's
w/ HSI. You said draft sw. is bypassed. The stuff I
work with that sw. has to be open before the firing
sequence begins. Would seem that...
Been on vacation, heading home today. How do I log out?
Captain Morgan & vanilla coke. Hmmm, sounds good, think
I'll mix one up and get an early start.
If it is painted green it has a schraeder in it.
Oops.Reread your post. Kept seeing Lennox and thought you were wanting to put the control on a Lennox furnace.
Humidity is controlled by the variable speed blower slowingdown to reduce humidity.
Yoy can't use the Infinity control on anything but an
Infinity furnace.
Yep.
Jeff, Grangeville, Idaho
Went back next day, put a guage on a six inch hose and found suction pr. @ 31#, specs say 34#. Tweaked the bypass
about 1/8 turn to get 34#. Don't know if I compensated for another problem by doing...
Sorry, had to get off here for awhile. Have oil serarater
and filter. Temps shown were after I thawed it out, got
lots of water. Looks like fixing this thing will involve
changing refr. either due...
Hankison m/n 8010. Evap iced up and stopped air flow thru
the drier in early July. Thawed it out and thought we were
O.K. Customer called @ quitting time today and said it has
iced up 3 or 4 times...
Get a match.
Looking for a supplier in the northwest.
If your superheat @ box was 4 and 95 @ compr. and you adjusted valve to get 20 @ compr. it would seem to me that your evap would have to be flooded and your suction line is now your evaporator. Do...
I know what it is and where to get one butit's a secret.
If I told you I would have to have you killed.
Lots of comments about who gets what, anybody know what's
legal. I know it could vary from state to state but there
are federal labor laws. Seems to me that if employer is
controlling your...
Idaho requires an HVAC Contractors license for the business.
Each tech needs an HVAC license to install or service
equipment. Just went into effect Jan. 1.
Thanks, I'll check w/ our distributer Monday.
Got any more info on that manual such as a number or a
title? Is it available for downloading @ the partners site?