Search:

Type: Posts; User: The Reaper

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    215

    Thanks for the replies. I'll post with results.

    Thanks for the replies. I'll post with results.
  2. Replies
    3
    Views
    215

    AX Tuning Policies

    Is there any good information on proper setup of tuning policies? Thanks in advance.
  3. Replies
    8
    Views
    449

    alliedtech, Did you ever resolve this? I'm in...

    alliedtech,
    Did you ever resolve this? I'm in the same situation right now.
  4. Replies
    2
    Views
    324

    Thanks for the info. I did find the document and...

    Thanks for the info. I did find the document and it answered my question.
  5. Replies
    2
    Views
    324

    JCI Brain Fart

    Can somebody tell me what the proper point mapping is for a PMK point out of a DX 9100? I'm swapping out an N30 for an FX-60 and it's been a while. Thanks
  6. Replies
    0
    Views
    118

    KMC Alarm Issues

    I just took over a KMC system and I'm trying to get the alarms to work. Certain alarms are working fine, emailing and displaying in the alarm viewer, but when I add an alarm, I can't seem to get it...
  7. Replies
    10
    Views
    488

    You can use the .prn file, which is created when...

    You can use the .prn file, which is created when you save the uploaded file, to add the points. You can just put the path of the file in the resource file slot of the controller which is found on the...
  8. Thread: Metasys CT

    by The Reaper
    Replies
    4
    Views
    383

    You're going to be looking inside the main panel...

    You're going to be looking inside the main panel for the tenant area. There will be some donuts around the main feeders to the panel. I would have a licensed electrician available for assistance...
  9. Replies
    6
    Views
    1,482

    Bingo!!!

    Bingo!!!
  10. Replies
    1
    Views
    191

    Cancel this thread. I found a manual for this...

    Cancel this thread. I found a manual for this device and it is BACnet IP.
  11. Replies
    1
    Views
    191

    Alerton BTI-100

    I just took over a building that is half Honeywell C Bus to a Jace 7 and the other half is Alerton. The Alerton has Tux's for controllers that report to a Tux Gateway and then to a BTI-100. My...
  12. Replies
    6
    Views
    1,482

    This Guy Ran Out Of Washers

    Found this gem today. I couldn't find the key to the panel. Luckily, I had one on my key chain.
  13. Replies
    7
    Views
    351

    I think Matrix nailed it. I've had this be the...

    I think Matrix nailed it. I've had this be the problem more times than I care to remember.
  14. Replies
    15
    Views
    570

    Thanks Amigo. Good information.

    Thanks Amigo. Good information.
  15. Replies
    15
    Views
    570

    I think both situations would have the same...

    I think both situations would have the same result. I'm not 100% sure and maybe somebody with more BACnet experience will chime in, but I think that these settings would affect peer to peer...
  16. Replies
    15
    Views
    570

    If your Max Master is set to 10 on a global...

    If your Max Master is set to 10 on a global controller, the only ms/tp controllers that will communicate are address 10 and below. If your device is address 121, your Max Master needs to be at least...
  17. Replies
    4
    Views
    306

    I could be wrong, but couldn't you use a 24vac...

    I could be wrong, but couldn't you use a 24vac incremental output in the program. This uses a pair of outputs and pulses them according to your PID output. You can set your stroke time and min PWM...
  18. Replies
    4
    Views
    306

    I know JCI offers a PCT custom programming...

    I know JCI offers a PCT custom programming course. I learned mine by trial and error. Is there a specific sequence you're trying to accomplish or are you just trying to learn more?
  19. Replies
    15
    Views
    762

    Never thought of using XOR's for a Flip Flop....

    Never thought of using XOR's for a Flip Flop. Thanks Matt.
  20. Replies
    15
    Views
    762

    I just looked at your logic. Try getting rid of...

    I just looked at your logic. Try getting rid of the AND (10) block and put in a BV output in its place. That looks like it will work.
  21. Replies
    15
    Views
    762

    You're very welcome. You can make your own pulse...

    You're very welcome. You can make your own pulse timer with a timer, a NOT block and an AND block. Don't worry about the Last Value blocks. They are JCI specific and are not needed for the logic to...
  22. Replies
    15
    Views
    762

    I don't know about the programming for Can2go,...

    I don't know about the programming for Can2go, but this can be easily done with a little logic. I would compare the temp to a setpoint and use the logical result to trigger a flip flop. The output of...
  23. Replies
    10
    Views
    1,356

    I was able to get things running. Small tweaks to...

    I was able to get things running. Small tweaks to the program and things worked well.
  24. Replies
    10
    Views
    1,356

    Yes, it was a retrofit. They did have a schematic...

    Yes, it was a retrofit. They did have a schematic from the old system. What kills me is that it probably would have taken about 1/2 hour longer to make the panel look good. I don't know for sure but...
  25. Thanks. I used machine screws and nuts/washers to...

    Thanks. I used machine screws and nuts/washers to attach the door panel. I'm looking for a nice BACnet touch screen for the front. That will cover the screw heads nicely. It is a KELE RET enclosure.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event