Search:

Type: Posts; User: gkstriper

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,339

    Thanks for the explanation......very concise!

    Thanks for the explanation......very concise!
  2. Replies
    4
    Views
    1,339

    SIEMENS Slope & Intercept

    Does anyone have a solid understanding as to why we have to calculate slope & intercept? What is the proper way to use the slope & intercept calculator in INSIGHT? What exactly is the "device range"...
  3. Replies
    8
    Views
    1,361

    Dansky, This is great info, thanks so much for...

    Dansky,

    This is great info, thanks so much for this!
  4. Replies
    8
    Views
    1,361

    Danski, Thanks for your response. I didn't...

    Danski,

    Thanks for your response. I didn't know if you may have had any PDF's on the ADAPTS you could email. Sounds like adapt statements can be quite the hassle to deal with.
  5. Replies
    8
    Views
    1,361

    SIEMENS PPCL "ADAPT" Statement

    Been at this awhile but I can honestly say that I don't know very much about the "ADAPT" statement. I was hoping someone could shed some light.

    I'd like to know just exactly how it functions as...
  6. Replies
    1
    Views
    812

    SIEMENS SKD-62U NOISY Actuator

    Does anyone have an opinion on why these actuators are so noisy? I've installed a good amount of these and it's usually hit or miss as to how much noise they'll make when they stroke. I have taken...
  7. Replies
    3
    Views
    651

    Thanks guys.....couldn't quite recall the format.

    Thanks guys.....couldn't quite recall the format.
  8. Replies
    3
    Views
    651

    SIEMENS PPCL Local Variables

    Does anyone remember how to run a panel point log report on Local Variables ($LOC's)?
  9. Replies
    1
    Views
    1,642

    SIEMENS "adapt" statement (PPCL)

    I'm quite familiar with how to write a LOOP statement but have had very little exposure to the newer "ADAPT" statement. Does anyone have anything in writing, perhaps a section out of a training...
  10. Replies
    13
    Views
    778

    I also have used the radio shack usb to rs-232...

    I also have used the radio shack usb to rs-232 converter with good luck. Have you installed the drivers that came with the device?
  11. Replies
    6
    Views
    559

    It's my biggest frustration dealing with these...

    It's my biggest frustration dealing with these new converters or "dongles". The fact that a COM port has to be assigned to them is particularly at issue because I communicate with SIEMENS and JCI...
  12. Replies
    24
    Views
    4,838

    Neonhomer.......... I actually have the...

    Neonhomer..........

    I actually have the dos version. Wincis is the one i'm looking for. I'd really appreciate a copy if you had the time.

    Thanks for the consideration.
  13. Replies
    24
    Views
    4,838

    Siemenstech29..... Could I trouble you for a...

    Siemenstech29.....

    Could I trouble you for a copy as well? I've posted myself for quite some time now in search of a copy of wincis with no luck.

    thanks for the consideration.
  14. My take on Siemens.....

    Just thought I'd toss in my two cents. I can't say that I know much about the inner workings at JCI but I have seen and heard my share when it comes to Siemens.

    I have worked in a sight for nearly...
  15. Replies
    5
    Views
    1,581

    SIEMENS Datamate Base Advanced

    I've just recently started using Datamate Advanced. Does anyone understand why this program doesn't act real-time similair to Insight. For example, I don't understand why if I edit a point, the point...
  16. Replies
    24
    Views
    1,455

    Beer 30....right on

    I agree with beer 30, we have similar issues running 100% outside air with no face and bypass. I also ramp the discharge air down slowly on start up. This causes your control valve to go wide open on...
  17. Replies
    24
    Views
    1,455

    Is the unit tripping out while running or on...

    Is the unit tripping out while running or on start-up?
  18. Replies
    21
    Views
    3,557

    Thanks for the time........ Let me add that...

    Thanks for the time........

    Let me add that along with the panel we also added 2 TEC's to FLN-1.


    I only have "read only" access to system profile so I had someone else drag over a field panel...
  19. Replies
    21
    Views
    3,557

    SIEMENS Insight/MBC questions........

    I'm sure one of you can steer me in the right direction here.

    I need to have a better undestanding of whats going on with an MBC panel I just installed.

    We created several new points as well as...
  20. Bob, Go to the Report Builder, scroll down to...

    Bob,

    Go to the Report Builder, scroll down to the bottom of the reports list and select "user accounts report".

    That will display your access level.
  21. Sounds like you've got it all. Point Editor...

    Sounds like you've got it all.

    Point Editor allows you to edit existing points as well as add new points.

    PPCL Editor allows you to edit existing programs as well as add/write new ones.
    ...
  22. Replies
    27
    Views
    6,409

    So then I take it you're not using a 2000 btu per...

    So then I take it you're not using a 2000 btu per outlet rating to determine the # of outlets.

    Is this a rule-of-thumb that works for you, perhaps based on desired noise level??
  23. Replies
    27
    Views
    6,409

    I went with Unico for my existing living space...

    I went with Unico for my existing living space and an LV for my new addition. There's no doubt about the cost difference for HV. I would definitely stick with the LV if you have the duct space....
  24. Replies
    3
    Views
    418

    Doesn't sound right. I'd be asking the same...

    Doesn't sound right. I'd be asking the same question. I would definitely voice your concern now. You know as well as I do that you'll be the one expected to perform miracles on this unit once it...
  25. Replies
    4
    Views
    600

    All the Siemens Techs continue to purchase and...

    All the Siemens Techs continue to purchase and use DELL laptops as they still supply serial ports. Those USB adapters or dongles as they are described are a royal pain in the ass because of the...
Results 1 to 25 of 36
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event