yes 90% furnaces
Type: Posts; User: iowa tech
yes 90% furnaces
can a exchanger be check by blocking off intake pipe turning on fan only using a manometer hook up intake box?
what is the best way of replacing one?
unsolder or cutting it out with saw
Orfice was missing
so is Inducer Orifice in blower or Header Box?
Temp is about 135 in flue
New c blower install by first tech
Yes 90%
model m3rl080a
ser m3a050301139
keeps tripping limit on combustion blower
work alright while i there
something over heating but what
any help?
so if furnace kicks in at 35*
how do you save money?
when it cold and furnace runs anyway
where in iowa are you?
so have you called them back out?
at the valve and t-stat
new valve out of box
old valve was doing same thing that why i replaced it
ok thanks
10psi at valve
system has 10psi steam pressure
installed new VP525C1024 VP525C Series Pneumatic Radiator Valve will not close off steam. i have 10psi at control and at valve actuator. valve had 3-10 psi spring also tryed the 2-5 spring still not...
Contact Information
AIRE-FLO
2100 Lake Park Blvd.
Richardson, TX 75080
1-800-982-2333
installed new VP525C1024 VP525C Series Pneumatic Radiator Valve will not close off steam. i have 10psi at control and at valve actuator. valve had 3-10 psi spring also tryed the 2-5 spring still not...
model asp3125-347
also check plug with no motor had 120 to net on one leg
check other leg high speed 65v low 75v does that help
i think i have a bad motor right
ok i know i need help on pneumatics
do you know any thing about how the switch controls the motor?
so do they power both windings thru the trans at same time?
do you know how the switch is wired?
still need to know how the switch should be wired in case someone has been playing
not sure what pe switch is
i have three button switch off hi low
high speed runs all the time switch can only turn fan off
just start new job that works on them,so real new to them
i can do that
would like to have wiring diagram to work from to make it easyer
so with no numbers how can i get wiring diagram
do all units have relays ?
back of switch has 7 spots for wires don't know what is what
yes
hi
low
off
I have a school with old Herman Nelson Unit ventilators. This stuff is from 1967 and is all pnuematics. Does anyone have any literature on this stuff? i'm new to pnuematics.motor low speed not...
I have a school with old Herman Nelson Unit ventilators. This stuff is from 1967 and is all pnuematics. Does anyone have any literature on this stuff? i'm new to pnuematics.motor low speed not...
its on the unit find it
42 years old
need more air flow upstairs (spit level ) for comfort and filtering
i have g32v fan on runs at 70% can this be changed also if so can it be found at davenet or could you post in pro area how ?
sp 0.0 wc thur 0.8 wc will give 1060 cfm low
sp 0.0 wc thur 0.8 wc will give 1105 cfm medium low
sp 0.0 wc thur 0.8 wc will give 1260 cfm medium high
sp 0.0 wc thur 0.8 wc will give 1330 cfm ...
my furnace has vs motor, chart say sp 0-.8 will give me 1330 cfm max so what sp should i use to set up duct work
what ones do you use? what the best?
thanks
does the furnace come on or just hot air out of vents?
a/c still running?
why no2 in lines?
you would know if compressor is pumping at all. if it can't pump back then you have bad compressor (valves).or maybe a bad start cap.
can you pump freon back into condenser by closing service valves?
does it pump back?
did the compressor pump back?
is the compressor running, same pressure both sides not running or bad
what do you mean amps 7., 6., 5.?
could have to much pressure with good valve. had one make noise when turning on and off.
could you show how to do it please
so why does lennox say 16"x25" filter is what you need for 3 ton furnace?
so what happens with variable speed?
tring to find btu output of system
can you tell how this would be done? no manual ifo
thanks
how do you find condenser cfm?
should you use same asp for supply and return