Search:

Type: Posts; User: fordrules

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    555

    I've seen some female techs mentioned on here but...

    I've seen some female techs mentioned on here but never seen any in my area. Good to hear more are entering the trade.
  2. Replies
    40
    Views
    2,004

    fieldpiece sc56

    fieldpiece sc56
  3. Replies
    19
    Views
    1,068

    We use 3 in 1s on older and less common...

    We use 3 in 1s on older and less common compressors all the time. Some have been running for years this way. Anything new gets factory components.
  4. Replies
    43
    Views
    1,704

    What vegas said. And anything with a txv.

    What vegas said. And anything with a txv.
  5. On the cm3 controller, the bin stat is plug #7. ...

    On the cm3 controller, the bin stat is plug #7. If you unplug the connector and the full bin light shuts off, the bin stat is bad.
  6. Does it have a bin stat?

    Does it have a bin stat?
  7. Replies
    7
    Views
    436

    Bin stat?

    Bin stat?
  8. My supply houses still have them.

    My supply houses still have them.
  9. Replies
    33
    Views
    5,193

    I don't see a trap. I had a call at a church for...

    I don't see a trap. I had a call at a church for a water leak last week. He said the plumber was there and re did the drain lines earlier this summer, and they had water issues. The plumber didn't...
  10. Replies
    3
    Views
    325

    You could pull the belt off and check the frost...

    You could pull the belt off and check the frost pattern to see if everything is feeding correctly.
  11. Replies
    7
    Views
    1,824

    We use it for r12 medium temp, works good.

    We use it for r12 medium temp, works good.
  12. Replies
    35
    Views
    1,296

    Did you cap unused leads?

    Did you cap unused leads?
  13. Replies
    15
    Views
    985

    We use MP66 for low temp. MP39 or r420a for...

    We use MP66 for low temp. MP39 or r420a for medium temp.
  14. Replies
    10
    Views
    489

    I had an s model a while ago where the water...

    I had an s model a while ago where the water level sensor failed because the heat shrink wasn't sealed on top and the wire corroded. Been checking for that on cleanings now, and have found a few...
  15. Replies
    32
    Views
    1,824

    I take my cordless drill with a wire brush...

    I take my cordless drill with a wire brush attachment to get most of the rust off. Touch up with sandpaper, and spray with kroil. Then I try my puller and some heat if needed. If that doesn't...
  16. Replies
    12
    Views
    599

    Use a core tool as mentioned, or use ball valve...

    Use a core tool as mentioned, or use ball valve hoses. Fill hoses with refrigerant, zero scale, weigh in charge.
  17. Replies
    33
    Views
    2,130

    If its single phase, start components ok?

    If its single phase, start components ok?
  18. changing the square condenser fan motors on...

    changing the square condenser fan motors on randell prep tables.
  19. Check the dump valve.

    Check the dump valve.
  20. Replies
    18
    Views
    1,052

    I unloaded alot of duplicates and tools I never...

    I unloaded alot of duplicates and tools I never used when I got a replacement veto xl. Unfortunately, when I was lowering it down off a roof last week, the rope slipped and the bottom plastic is...
  21. Replies
    23
    Views
    1,454

    I made that call a few years ago. I believe...

    I made that call a few years ago. I believe cooling logic was similar to heating logic. Not sure how many cycles it takes to establish a baseline.
  22. Replies
    23
    Views
    1,454

    I called Honeywell tech with the same question...

    I called Honeywell tech with the same question you have, "what controls the staging?". They said it is a time/temperature algorithm based on previous cycles.
  23. Thread: Resistors

    by fordrules
    Replies
    10
    Views
    779

    Thanks again!

    Thanks again!
  24. Thread: Resistors

    by fordrules
    Replies
    10
    Views
    779

    Thanks for the input guys. Timebuilder, would...

    Thanks for the input guys. Timebuilder, would you happen to know the part number for that kit?
  25. Thread: Resistors

    by fordrules
    Replies
    10
    Views
    779

    Resistors

    I am looking to get a small assortment of resistors for various testing purposes (economizer controls, trane voyager test mode, etc). What watt resistor would be best for this? I see there are 1/4,...
Results 1 to 25 of 289
Page 1 of 12 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event