Search:

Type: Posts; User: klrogers

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. You have mail

    You have mail
  2. Replies
    1
    Views
    130

    Check out the "Report Service" Kevin

    Check out the "Report Service"

    Kevin
  3. I am not sure that this will work with all...

    I am not sure that this will work with all versions and manufacturers, but you can try this:

    Copy the config.bog file
    Create a dummy station on your laptop
    Copy the copied config.bog into the...
  4. Replies
    45
    Views
    1,460

    The full website address is :...

    The full website address is : "http://www.pecomanufacturing.com/assets/docs/datasheets/t180-t170-peco-data-sheet.pdf" hopefully it will not get shortened when I post this.

    I am not a "Trane" guy,...
  5. Replies
    45
    Views
    1,460

    A lot depends on your type of tenants, High end...

    A lot depends on your type of tenants, High end condo's you need to keep them happy at all times, doing the best you can with what you got. Section 8 buildings or similar, Heat Nov 15th until Mar...
  6. Replies
    45
    Views
    1,460

    Ideally the thermostats in the resident spaces...

    Ideally the thermostats in the resident spaces should know which mode the system is in, this can be done either of two ways, a communicating thermostat connected back to the control system (probably...
  7. Replies
    2
    Views
    321

    Good material for controls techs.

    Contemporary Controls has put together a book that contains various previously published articles and some updated stuff, it is titled Network Communications for Buildings, and covers in fairly fine...
  8. Replies
    2
    Views
    190

    I suggest that you ask your question in this...

    I suggest that you ask your question in this section: http://hvac-talk.com/vbb/forumdisplay.php?1-AOP-Residential-HVAC
  9. Replies
    14
    Views
    476

    Are you sure you are talking about the same...

    Are you sure you are talking about the same thing, the niagaraDriver device limit is for stations pulled in to the niagara network not Jaces on the navigation tree.
  10. Thread: EC BOS ?

    by klrogers
    Replies
    4
    Views
    171

    Or Platform Service container view

    Or Platform Service container view
  11. Replies
    8
    Views
    461

    Thanks for the links. I'm happy to help you or...

    Thanks for the links.

    I'm happy to help you or anyone out when I can, I have received help from many other members over the years and like to return the favor. Despite its occasional rants and...
  12. Replies
    8
    Views
    461

    "print index all" will give you a list of the...

    "print index all" will give you a list of the control drums

    then "p dr {drum #}" to display drum logic, I recommend capturing the output and printing it out if possible.

    You might want to "P...
  13. Replies
    8
    Views
    461

    Be careful using the edit command, you are...

    Be careful using the edit command, you are working on a live program :)
  14. Replies
    8
    Views
    461

    564511 See if this helps, thats from H...

    564511

    See if this helps, thats from H (Return)

    usually use something like "Print Drum 150" which can be shortened to "P DR 150"
  15. Replies
    7
    Views
    480

    Most FX-60's have the embedded WB, with that you...

    Most FX-60's have the embedded WB, with that you can do 90% of what you can do with the PC version.

    Kevin
  16. I have to agree with MatrixTransform the layout...

    I have to agree with MatrixTransform the layout of your stations is very important. I have though experience found that the time spent designing the stations before you even start building a station...
  17. Replies
    16
    Views
    570

    Jace ports might be changed from default

    Jace ports might be changed from default
  18. Turn on FTP (by shell access if needed), and FTP...

    Turn on FTP (by shell access if needed), and FTP in. Still need platform user and password but if you are in shell easy enough to reset.

    Kevin
  19. Replies
    17
    Views
    1,534

    If you want to get away from the JAVA issues use...

    If you want to get away from the JAVA issues use Hx or mobile app pages, either of these use JAVA.

    Kevin
  20. Replies
    4
    Views
    544

    Sounds like the perfect application for you to...

    Sounds like the perfect application for you to write a program object for :) It certainly can be done on a wire sheet but a PO would be much better and re-usable.
    There are some examples of PO's...
  21. If the set point editor is changing the "date...

    If the set point editor is changing the "date range" in the source node I would say that that part is probably working OK. I have attached screenshots of:
    1) Wiresheet with OAT source node property...
  22. One quick thought, do you have ALL the date...

    One quick thought, do you have ALL the date ranges on all the source nodes linked together? They all need to be on the same date range.
  23. Look at bit different this week ;) 555771:)

    Look at bit different this week ;)


    555771:)
  24. See if these help, I throw together a px page...

    See if these help, I throw together a px page using an existing seriesTranform set. When I change the date range, save and then hit refresh the graph updates. Now I know it would be better for it to...
  25. Replies
    6
    Views
    351

    You could something with the "alarmCountToRelay"...

    You could something with the "alarmCountToRelay" module in kitControl. Or something using a BQL statement.

    Kevin
  26. 550691 set point field editor from kitPx, this...

    550691

    set point field editor from kitPx, this screenshoot should help you see how it is attached to the transform graph. I don't now how you would use the "time range" choice, that would need to...
  27. You have to use the composite editor to expose...

    You have to use the composite editor to expose the time range slot, link the slots together so they all change, and use a "set point field editor" in your px view to change the time range on the...
  28. If you can upgrade to 3.7 it makes what you are...

    If you can upgrade to 3.7 it makes what you are trying to do much more practical, using a new module call seriesTranform.

    Kevin
  29. Thread: Fx60 login

    by klrogers
    Replies
    7
    Views
    242

    Resetting username/password in serial shell only...

    Resetting username/password in serial shell only changes the Platform username/password not the station username/password.

    I can't say much more on this open forum, particularly to a new member....
  30. Replies
    16
    Views
    1,496

    I can't believe that this post is getting so much...

    I can't believe that this post is getting so much attention, the PO is probably a DIY home owner ;)
  31. Replies
    9
    Views
    387

    Try here: 536791 Never really found a use...

    Try here:


    536791

    Never really found a use for a pie chart on a single history :)
  32. Replies
    11
    Views
    1,230

    That's a short sighted and old school quote from...

    That's a short sighted and old school quote from your office, unfortunately many customers are not informed enough about building automation and are blindsided into accepting such changes to THEIR...
  33. Honeywell Gray Manual is excellent for control...

    Honeywell Gray Manual is excellent for control strategies, but this http://www.enerlon.com/?wpsc-product=building-automation-control-devices-and-applications-hardcover-duplicate covers the more...
  34. Thread: Jace and SMS

    by klrogers
    Replies
    0
    Views
    216

    Jace and SMS

    Anyone using and can recommend a good external serial GPRS modem for use with a Jace to send SMS messages? We are currently using the Tridium supplied internal modem with a wireless SIM card and high...
  35. 522421Set up an alarm class lets say...

    522421Set up an alarm class lets say "BoilerFailAlarmClass", then route that to your email recipient (and console recipient usually). Use this new class it the set up of your alarm extension.
  36. +1, pity we can't do N2 tunnelling ;)

    +1, pity we can't do N2 tunnelling ;)
  37. You have to create identical alarm classes in...

    You have to create identical alarm classes in both the Jace and the Supervisor to use 'use existing'
  38. Do you have %alarmData.msgText% in the body of...

    Do you have %alarmData.msgText% in the body of your email recipient?

    Kevin
  39. Thread: HVAC Pro

    by klrogers
    Replies
    44
    Views
    3,257

    Get the B&B USOPTL4 and you can then connect...

    Get the B&B USOPTL4 and you can then connect directly on the N2 network, you should disconnect any other supervisory controls from the network, i.e. N30, FX60 etc. If you want to connect using the...
  40. 521031 Change the "Replace" with "Use...

    521031

    Change the "Replace" with "Use existing"

    Kevin
  41. Thread: HVAC Pro

    by klrogers
    Replies
    44
    Views
    3,257

    I have heard that some guys have been able to...

    I have heard that some guys have been able to install it on Windows 7, but that might have been a 32 bit version of Win 7. Myself I put it on a virtual machine (VmWare) running XP. Not sure if it...
  42. Thread: Economizers

    by klrogers
    Replies
    5
    Views
    738

    Try this for starters ...

    Try this for starters

    http://www.virginiaair.com/index.php/contractors/documents/hot-sheets/doc_download/462-honeywell-economizer-troubleshooting

    Kevin
  43. Replies
    2
    Views
    277

    Should be as simple as animating the background...

    Should be as simple as animating the background property of the bound label, right click on it, choose animate, choose boolean to simple, choose colors for True and false.

    Kevin

    EDIT: if you...
  44. Replies
    1
    Views
    331

    If you had access to the Vykon Pro module then...

    If you had access to the Vykon Pro module then there is a built in module that would do the job.

    515971

    515981


    Kevin
  45. Replies
    5
    Views
    575

    I see your are in Virginia, and you are talking...

    I see your are in Virginia, and you are talking about Southeast, do you mean Southeast Virginia, if so are you talking about Damuth Trane?

    Kevin
  46. Replies
    13
    Views
    519

    I know of such commands for Ax Jaces, not sure if...

    I know of such commands for Ax Jaces, not sure if there is such a thing for R2 ones, the Ax ones are not recommended to be used according to the powers that be, they should be used only as a last...
  47. Replies
    2
    Views
    330

    For the first question, you could modify the...

    For the first question, you could modify the setpoint checkbox widget from kitPx to achieve the required actions, just take any the checkbox graphic and use a normal button to toggle between...
  48. Replies
    12
    Views
    524

    Make sure that you enter the facet is '...

    Make sure that you enter the facet is ' maxOverrideDuration' note the first letter is in lowercase, small things like that can throw you for a loop.

    Kevin
  49. Replies
    6
    Views
    739

    One of many options might be...

    One of many options might be http://www.pelicanwireless.com/

    Kevin
  50. I think that ones level of access controls who...

    I think that ones level of access controls who can use that feature, I don't have that ability.

    Kevin
Results 1 to 50 of 1000
Page 1 of 20 1 2 3 4

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event