Search:

Type: Posts; User: troyport

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. thanks for the responses..

    thanks for the responses..
  2. many thanks, and one last burning question.

    Hello all.. I have been posting and reading here for many years. The information I gained by all the professionals here has been invaluable. I had a basic propane furnace / old school AC unit when...
  3. new board in HP change the defrost procedure?

    Goodman 16 seer 2 stage HP with modulating furnace and CTK02 t-stat.. from the time it was new, I would get a "No indoor blower" trouble code when coming out of defrost. Finally, Goodman had a fix...
  4. Replies
    2
    Views
    248

    Through the wall unit at a very nice inn

    The Inn at Ohio Northern University, recently completely upgraded including new through the wall HVAC units. When we checked in, the room was cool even though it was set at 75 degrees. Then...
  5. general question for all you professionals..

    Forgive me if this is the wrong place for this post. I was looking at the wall of shame area, came across the HVAC system built by the engineer, and I wonder if any of you add components to your...
  6. Replies
    3
    Views
    366

    Filter is always perfectly clean. But if is was a...

    Filter is always perfectly clean. But if is was a dirty filter and therefore bad indoor airflow, wouldn't that tend to lower the suction and trip out on low pressure?
  7. Replies
    3
    Views
    366

    high pressure trip.

    Goodman 2-stage heat 16 seer heat pump, communicating system. Once in a while, via the t-stat I will check for error codes. Found that over the past 2 months, it has tripped out on high pressure /...
  8. Great news. Thanks for the reply.

    Great news. Thanks for the reply.
  9. That's my question too. Was it just a "shot in...

    That's my question too. Was it just a "shot in the dark to shut the guy up" board or is it a documented problem that now has a verified fix.
  10. I've had the HP for a year, and this is the first...

    I've had the HP for a year, and this is the first time anyone anywhere has ever said anything. Couldn't have a conversation at all, then suddenly Goodman has a new board and tells my tech "problem...
  11. Goodman no indoor blower error code, solved?

    Posted about this before, but no one here was able to offer help, but have helped in so many other ways I thought I would share this:
    3 ton 16 seer 2 stage HP with modulating gas furnace and CTK02...
  12. So is it safe to assume that no one has ever done...

    So is it safe to assume that no one has ever done this? And also no one has ever looked at the network communications as a computer and could benefit from cabling as such?
  13. Any Goodman / Amana guys have thoughts?

    Any Goodman / Amana guys have thoughts?
  14. twisted pair for communication wires, maybe solve occasional communication glitches.

    Goodman communicating system, uses a 4 wire hook up. I saw in the manual that communications can be improved if shielded, twisted pair cable is used for the data lines. So that would mean, as I...
  15. random thoughts after first winter with dual fuel system

    Well, I guess with this winter it might be far from over. Goodman 2 stage 16 seer HP with modulating propane furnace and CTK02 t-stat. Overall, I just love this system. I am amazed how well the HP...
  16. It plugs directly into the board, so not exposed....

    It plugs directly into the board, so not exposed. But probably a bad connection, unless it is a board problem (bad solder joint, hairline crack, etc. I will ask him when it comes out in spring,...
  17. outdoor ambient temp sensor blanking out.

    Goodman 2 stage 3 ton HP, with modulating furnace and CTK02 t-stat. During our first real cold snap about a month ago, below zero outside, come home and the HP is running. I have the dual fuel temp...
  18. Replies
    11
    Views
    658

    I understand.. if it isn't cheaper for you then...

    I understand.. if it isn't cheaper for you then it might as well sit in my garage from your point of view. That makes sense, and I appreciate your honesty. I am in NE Ohio, could this stuff even be...
  19. Replies
    11
    Views
    658

    No clue what it is worth, but I could google it. ...

    No clue what it is worth, but I could google it. Any fair price is better than what I am getting for it sitting in the garage. Can the stuff be shipped without a hassle?
  20. Replies
    11
    Views
    658

    the original nat gas burner and valve for an 80K...

    the original nat gas burner and valve for an 80K Goodman GMVM, never used. The furnace was converted to Propane. And when I bought my house in 1999 it had an R22 AC unit that was not working quite...
  21. Replies
    11
    Views
    658

    can a homeowner sell stuff here?

    Like the subject says..
  22. Replies
    4
    Views
    397

    thank you very much.

    thank you very much.
  23. Replies
    4
    Views
    397

    No picture, and frost was not thick. It was...

    No picture, and frost was not thick. It was probably just starting to restrict airflow, hence the slight drop in temperature rise.
  24. Replies
    4
    Views
    397

    outdoor coil frosting in a pattern.

    Perfect conditions yesterday for frosting of a heatpump. I noticed mine was frosting in a pattern, that eventually filled in almost completely before it went into defrost. When it was completely...
  25. Replies
    8
    Views
    739

    Thanks for the replies. But why was this moved...

    Thanks for the replies. But why was this moved to "tech to tech"? I am not a tech!
  26. Replies
    8
    Views
    739

    propane vs. natural gas

    See a lot of threads here pertaining to this.. But exactly why is propane harder on equipment than natural gas? Never lived in the city, been on propane my whole life, nearly 50 years.
  27. Replies
    15
    Views
    919

    Agreed on the 60k, but too late now! Regarding...

    Agreed on the 60k, but too late now! Regarding the ductwork, in my case I am sure that is okay even for the furnace I have, on high fire with proper temp rise, the static pressure in the ducts are...
  28. Replies
    13
    Views
    978

    Oh... well, who knows where the heck that little...

    Oh... well, who knows where the heck that little bracket went! So essentially the little sensing bulb is out in the weather, okay, then where it is now is a reasonable place. My installer told me the...
  29. Replies
    13
    Views
    978

    I have painted an incorrect picture for you, I am...

    I have painted an incorrect picture for you, I am sorry about that! This HP has a temp sensor on about a 12" lead that plugs directly into the main board of the HP. It is not connected to the...
  30. Replies
    13
    Views
    978

    Correct.

    Correct.
  31. Replies
    15
    Views
    919

    regardless of how much efficiency I am losing,...

    regardless of how much efficiency I am losing, just the fact that I did my best to get it right really is a bummer. We were not here when the house was built, so, who knows how good the walls really...
  32. Replies
    13
    Views
    978

    The wire leads are only about 12" long, no way to...

    The wire leads are only about 12" long, no way to get it too far away from the HP. Maybe this is why it is attached to the electrical flexible conduit.
  33. Replies
    15
    Views
    919

    well, it is very comfortable in here, and silent...

    well, it is very comfortable in here, and silent - since the blower never runs very fast. I suppose all I am losing is ultimate efficiency? One thing for sure, I can still use setbacks, even during...
  34. Replies
    13
    Views
    978

    Yes, I agree, needs to be outside, but where are...

    Yes, I agree, needs to be outside, but where are they generally mounted? I'm figuring not in direct sun, not where it can pick up temps (warm or cold) from the HP itself, but sheltered from direct...
  35. Replies
    13
    Views
    978

    outside temperature sensor

    Goodman HP 3 ton 2 stage 16 seer coupled to a propane mod. furnace and comfortnet t-stat. Get home from work today, -1 degrees outside, heatpump is running, even though the dual fuel set point is in...
  36. Replies
    15
    Views
    919

    50 %. It is a Goodman. Again, dang..

    50 %. It is a Goodman. Again, dang..
  37. Replies
    15
    Views
    919

    Amen to that.. The installer said the load calc...

    Amen to that.. The installer said the load calc numbers had me borderline, but since it was a modulating furnace it would be okay to go with the bigger furnace. Also, my windows are construction...
  38. Replies
    15
    Views
    919

    sizing tested at design temp.

    Thanks to this cold snap, finally having a sustained run at design temp. So my 96% 80k puts out 76.8k, and it is running non stop fluctuating between 55% and 65%. So average it at 60%, I am needing...
  39. Replies
    2
    Views
    434

    Thanks for the reply... I misled you. It ran at...

    Thanks for the reply... I misled you. It ran at 100% for 30 minutes to recover from 63 to 66, but after it was stable at 66 is when it would run at 50% for 45 minutes, off for 8, (repeating this...
  40. Replies
    2
    Views
    434

    oversized after all?

    2100 sq ft colonial built in 1989, load calcs were done at a design temp of zero degrees and 68 degrees inside. I was borderline between 60K and 80K. Bumping the inside up to 70 degrees put me at...
  41. Replies
    28
    Views
    3,063

    Well, I am happy to hear that I am not the only...

    Well, I am happy to hear that I am not the only one with the issue. I like the idea of cycling the fan blades, I bet I would void my warranty if I added a circuit to do that!! (It would not be that...
  42. Replies
    28
    Views
    3,063

    Exactly. My fan turns slower. It only seems to...

    Exactly. My fan turns slower. It only seems to need hi stage if it needs to come out of a setback, since I like to run the gas furnace below 25 degrees and don't ask the HP to work much on 2nd...
  43. Replies
    28
    Views
    3,063

    Thanks for the reply.. could make one pretty...

    Thanks for the reply.. could make one pretty easily.. if I cut a round piece of plywood the exact diameter of fan guard, how high do you think I would need install it? the guard I linked you to is...
  44. Replies
    28
    Views
    3,063

    happened again.. Not bad, but light snow...

    happened again.. Not bad, but light snow yesterday, HP was doing it's job nicely, 29 degrees outside. I look out and the unit is shaking some... more than I like. I shut it down to look, and...
  45. Replies
    2
    Views
    497

    To add.. this seemingly happened during a...

    To add.. this seemingly happened during a defrost.. Have had random "no ID blower" codes set during a defrost, and searching here I found someone else who had the same "no id blower" during defrost...
  46. Replies
    28
    Views
    3,063

    Funny, while sitting in the deer blind, was...

    Funny, while sitting in the deer blind, was thinking about spraying the blades with WD40 like I do my snowblower..
  47. Replies
    2
    Views
    497

    goodman b4 error code has me concerned.

    Goodman modulating 80K furnace with 2 stage 16 seer 3 ton HP and comm. t-stat. Wife texts me in the deer blind, says the t-stat display is red, call of service, status says "heat on" but nothing is...
  48. Replies
    28
    Views
    3,063

    thanks guys... that top looks pretty nice too,...

    thanks guys... that top looks pretty nice too, I've never seen a Goodman with that.
  49. Replies
    28
    Views
    3,063

    beenthere: A google search didn't show an...

    beenthere: A google search didn't show an alternate top for my unit.. or any other for that matter. Can you link me to something? Would love to see what it looks like.
  50. Replies
    28
    Views
    3,063

    beenthere: is it just louvered differently? Or...

    beenthere: is it just louvered differently? Or is it a shroud of sorts? Never heard of it.. but sounds pretty cool and would certainly solve the issue!!
Results 1 to 50 of 222
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event