Search:

Type: Posts; User: monkeyman#1

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Layers upon layers, a bit confining but...

    Layers upon layers, a bit confining but necessary. Had to go up on a roof during the last "vortex" in minus 12 deg f. actual. Wind blowing like a bugger, snow knee deep. Large building in an...
  2. Replies
    30
    Views
    1,462

    Went there this A.M. and fired up furnace. ...

    Went there this A.M. and fired up furnace. Checked manifold pressure, 4.25" WC. Adjusted to 3.5. Definitely not the cause of problem. Let furnace run and monitored temp at roll out switch. ...
  3. Replies
    30
    Views
    1,462

    Lol. Guess that I didn't think that through...

    Lol. Guess that I didn't think that through Coope. Between the phone ringing and trying to respond to you guys, my thought process was not at its peak. I am leaning more toward gas pressure, ...
  4. Replies
    30
    Views
    1,462

    Lol!!!! Fixed some frozen pipes this morning. ...

    Lol!!!! Fixed some frozen pipes this morning. Man, you guys got hammered. Minus 13 actual temp here yesterday, so yes, I have been busy too. Not complaining though, busy is good, it is the...
  5. Replies
    30
    Views
    1,462

    Return temp 70 degrees, supply temp 102 degrees....

    Return temp 70 degrees, supply temp 102 degrees. If anything a little low. Also I don't know where the temps were actually taken at.
  6. Replies
    30
    Views
    1,462

    No, but that was I thought that I had, which is...

    No, but that was I thought that I had, which is why I know the motor is original. I thought that maybe someone changed the motor out over the summer and put the wrong one in. How you been qwerty?
  7. Replies
    30
    Views
    1,462

    Thanks guys, air filter is clean, and just to...

    Thanks guys, air filter is clean, and just to put your mind at rest , this guy is a retired 636 service fitter, repaired commercial and industrial stuff for many years so is familiar with...
  8. Replies
    30
    Views
    1,462

    thanks for the responses. WMT, the furnace is...

    thanks for the responses. WMT, the furnace is cycling normally, approximately 8 minutes per cycle, leading me to believe that there is no blockage in supply. COOPE, anything is possible...
  9. Replies
    30
    Views
    1,462

    SOS need help asap

    Hey pros, I just received a call from a friend whose father-in-law is having problems with his furnace. The father-in-law is a retired 636 service fitter. Has an Arcoaire furnace, I do not have...
  10. Replies
    11
    Views
    679

    Hilarious!!!!

    Hilarious!!!!
  11. Replies
    33
    Views
    3,790

    They may have felts in them, whats the harm?

    They may have felts in them, whats the harm?
  12. Replies
    30
    Views
    2,315

    Just to let you know, all of us still from time...

    Just to let you know, all of us still from time to time come across our "firsts". That is the beauty of doing what we do, one never stops learning.
  13. Replies
    30
    Views
    2,315

    I have no advice to offer on this repair. Just...

    I have no advice to offer on this repair. Just wanted to say, job well done. Your journeyman sounds like a real joker. Keep your attitude of troubleshooting, not part swapping. It wont be...
  14. Replies
    21
    Views
    1,623

    How old is this unit. Did you check the heat...

    How old is this unit. Did you check the heat exchanger? Not familiar with this particular unit, but I wouldn't think there would be that much different about it. Hi temp limit? Stack switch?
  15. Replies
    6
    Views
    741

    As it should, you have no humidity control. ...

    As it should, you have no humidity control. Replace the humidistat.
  16. X2

    X2
  17. Replies
    11
    Views
    1,070

    My opinion? Run as fast as you can. I strictly...

    My opinion? Run as fast as you can. I strictly do commercial/industrial, however I have known guys that have worked hourly plus commisssion. If you have no scruples, this may be for you. Lots o...
  18. Replies
    7
    Views
    489

    I believe that I shed a tear there.

    I believe that I shed a tear there.
  19. Replies
    3
    Views
    530

    Be sure to use a center punch on the snapped off...

    Be sure to use a center punch on the snapped off portion of the bolt. Be sure that you are as close to center as possible. EZ out the snapped off bolt. Am not familiar with the sight glass...
  20. 56 percent silver and flux, does a great job, ...

    56 percent silver and flux, does a great job, nice flow
  21. Replies
    11
    Views
    970

    Sounds like there is a problem. Even with a dead...

    Sounds like there is a problem. Even with a dead battery, with unit plugged in to the wall charger, it should operate, mine does.
  22. Replies
    26
    Views
    3,631

    I have been doing this for a long time and I...

    I have been doing this for a long time and I still am learning
  23. Replies
    7
    Views
    1,948

    Seriously? Good luck

    Seriously? Good luck
  24. Replies
    9
    Views
    1,345

    I had a problem once, similar in nature, on a...

    I had a problem once, similar in nature, on a three door display freezer. Changed the fan delay switch and unit took off. Next day get a call, not working again. Arrive on site, it is working...
  25. Replies
    2
    Views
    572

    I assume that you have not done much reefer work....

    I assume that you have not done much reefer work. The answer to your question is yes.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event