Search:

Type: Posts; User: kc2dnw

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. I'm pretty sure Maxline's driver is EasyIO's old...

    I'm pretty sure Maxline's driver is EasyIO's old drivers and if so it is a P1 driver. The website doesn't have any detailed information.

    -Jeremy
  2. Replies
    2
    Views
    359

    Point modules disabled is an old thong for MBC's...

    Point modules disabled is an old thong for MBC's that is longer used. If you don't ave any points how do you know the modules aren't communicating? There will be no communication unless a point is...
  3. My opinion is the Tridium driver would be best...

    My opinion is the Tridium driver would be best accepted and useful for most contractors.

    If you build a BACnet gateway I would strongly recommend using virtual devices where each P2 device would...
  4. Replies
    14
    Views
    1,155

    I have used the RS232 version from this company...

    I have used the RS232 version from this company and had good luck with them. This is basically a point-to-point Ethernet connection.
    ...
  5. Replies
    59
    Views
    7,629

    From my limited experience you can have 1 master...

    From my limited experience you can have 1 master type device on the network, either the JACE or the SAGE but never both. Maybe there is a way to make the JACE act as a slave style device and exist...
  6. Replies
    4
    Views
    667

    Data Aire DAPIII issue

    Hey guys,
    I have a site that had 7 existing Data Aire DAPIII units that were communicating via BACnet/IP to the building Automation System but were unreliable. We converted to a Niagara AX based...
  7. There was someone who wrote an online interface...

    There was someone who wrote an online interface to be able to send e-mails and have them show up as Google Talk messages which may still work but Google Talk and XMPP have been obsoleted by Google...
  8. Replies
    6
    Views
    824

    Motor starter coils going bad

    Hello all,
    This is only sort of a controls issue but I am out of ideas and need some help. I service a schools districts controls and as part of that it seems I help with everything related because...
  9. I'm not sure how it works elsewhere but here in...

    I'm not sure how it works elsewhere but here in the US research is typically done by University's which are funded by grants. Grants come about to support something. So although science may not work...
  10. Replies
    15
    Views
    1,210

    Its been awhile since I had to work with a...

    Its been awhile since I had to work with a Daikain but If I remember the on/off button on the thermostat will override the BAS command, etc since they do not implement a priority array. This means if...
  11. Replies
    4
    Views
    560

    there seems to be an issue with the national...

    there seems to be an issue with the national weather service server where it wants a different date format which is not being provided by AX.

    have to wait for someone to figure out a patch
    ...
  12. Replies
    6
    Views
    553

    The TEC you have talks a proprietary protocol...

    The TEC you have talks a proprietary protocol called P1. Unless you want to convert everything on the wire to another protocol and redo your frontend then you are stuck wit Siemens an P1. There are...
  13. What is needed is a P2 driver for Niagara AX that...

    What is needed is a P2 driver for Niagara AX that allows us to replace Insight. The only current option is to keep insight and export points via BACnet which allows points to be seen but not much...
  14. Replies
    59
    Views
    7,629

    I also could use a copy. Currently working with a...

    I also could use a copy. Currently working with a site where I think some TX01 have been wired wrong since day they were installed.

    -Jeremy
  15. Thread: weather service

    by kc2dnw
    Replies
    7
    Views
    589

    A trick I use to get the correct settings is to...

    A trick I use to get the correct settings is to connect my laptop and use DHCP, then run an IPCONFIG /ALL to see what DNS, GATEWAY & SUBNET are being used on the network. The make sure these are the...
  16. I would use a Tridium Niagara AX based front end,...

    I would use a Tridium Niagara AX based front end, which is available from many vendors, and use the P1 driver for older ATEC's or BACnet MS/TP for the new BACnet versions. There is a P1 driver that...
  17. There appears to be some miscommunication here. ...

    There appears to be some miscommunication here.

    You have Siemens P1 devices and BACnet TEC's. What are you trying to do with these devices. It sounded like you were trying to integrate them into a...
  18. This questions is vague but 2 questions should...

    This questions is vague but 2 questions should help us start to give you an answer

    1) are they P1 ATEC's or BACnet ATEC's?
    2) What management station (frontend software) are you looking to...
  19. Replies
    6
    Views
    594

    Save station saves the currently running...

    Save station saves the currently running configuration to the drive of the JACE or supervisor running the station. Backup station saves a full backup of the station to the hard drive of the computer...
  20. Replies
    4
    Views
    384

    You likely have a code bug in your PPCL which...

    You likely have a code bug in your PPCL which constantly commanding the point in 2 different places to 2 different values.
  21. Replies
    8
    Views
    1,334

    There is no front end or router. There are 4 new...

    There is no front end or router. There are 4 new MACH Stats installed within the last 6 months. I need to tie these into the new system being installed which will have PUP and BACnet. They were...
  22. Replies
    8
    Views
    1,334

    Reliable Controls Mach Stat

    I need some help finding some documentation. We have a site we visited today where we are doing a project which includes replacing some panels, bringing in a bunch of panels using the PUP protocol...
  23. Replies
    1
    Views
    271

    Nothing I have ever seen and we use 3.6...

    Nothing I have ever seen and we use 3.6 extensively right now. Once in edit mode whatever element is selected is moved by the default block size set in your workbench with each push or if you old the...
  24. Replies
    2
    Views
    446

    Metasys uses an interesting architecture in that...

    Metasys uses an interesting architecture in that the "front end" is actually the NAE in the BACnet world. An ADX is just a data archive to store more data a graphics. The system is an Advanced...
  25. The KM Digital controllers only talk KMD digital...

    The KM Digital controllers only talk KMD digital and can not be brought into a front end other then Win Control or TotalControl. We are a KMC distributor and wish there was on option for older sites...
  26. Only the commissioning tool can do a true backup...

    Only the commissioning tool can do a true backup and restore through MMI, unless you have cracked the HASH key which I am not aware of anyone who has. Typically what people who "reload" through the...
  27. I used to be Siemens for many years and now have...

    I used to be Siemens for many years and now have an independent company and we really find the Niagara AX frameworks great. There are many P1 drivers available and for schools we replace the...
  28. My guess would be NO because anyone who has...

    My guess would be NO because anyone who has enough panels would have and need Insight to reload panels, do advanced features that just can e done through the MMI no matter how good a programer you...
  29. Replies
    10
    Views
    1,428

    P of 500, I of 5 and D of 0 is a standard staring...

    P of 500, I of 5 and D of 0 is a standard staring place. The type of sensors and output don't affect the loop and although they say there is a way to calculate the numbers in the MMI menu I usually...
  30. Replies
    6
    Views
    790

    If you command the point at Priority * in the...

    If you command the point at Priority * in the Jace and the out doesn't change to the value but the priority does change then the BACnet controller is either writing at a higher level than 8 or...
  31. Replies
    1
    Views
    540

    I have never used them but I would make sure your...

    I have never used them but I would make sure your JAVE MAC address for the MS/TP port doesn't conflict with anything else on the zone bus including the ZCU. If you disconnect the ZCU and just use...
  32. not a chance. It just uses the MMI port to...

    not a chance. It just uses the MMI port to constantly run a monitor report that it then strips into points values. If you have ever connected to an MMI port then you know how slow this can be. It...
  33. Replies
    2
    Views
    869

    How is the PXCM speaking BACnet MS/TP to your...

    How is the PXCM speaking BACnet MS/TP to your FX10? Are these BACnet PXCM with firmware 3.2 or later and just acting as a BACnet router, or are they a P2 PXCM and using the BACnet MS/TP integration...
  34. Replies
    3
    Views
    467

    Unless you have some reason to have the data in...

    Unless you have some reason to have the data in an FX70 and the import the points again via the Niagara protocol to the AX workstation I would bring them directly into the AX supervisor (or server as...
  35. Replies
    6
    Views
    885

    Couple things to check 1) your new devices,...

    Couple things to check

    1) your new devices, the MAC address for each device is unique on the wire you are connecting it to correct?
    2) Your new devices, the instance (Device ID) is unique across...
  36. Replies
    161
    Views
    31,998

    If you add your e-mail address to your profile...

    If you add your e-mail address to your profile you can be sent the configuration software but this only allows you to configure a few BACnet parameters. you would have to write/buy BACnet software...
  37. Thread: Siemens WIN CIS

    by kc2dnw
    Replies
    13
    Views
    2,215

    Siemens WCIS

    Once you have enough posts you can send me an e-mail to the address in my profile or place your e-mail address in yours and I cans end you a link.

    -Jeremy
  38. Replies
    14
    Views
    1,961

    You can't put an email in the forum but send me...

    You can't put an email in the forum but send me an email to the address in my profile and I will send some
    -Jeremy
  39. Replies
    14
    Views
    1,961

    The forum rules are to place your e-mail address...

    The forum rules are to place your e-mail address in your profile so people can contact you directly. I have heard recently you need 7 posts before you can update your profile.

    -Jeremy
  40. I agree and see these problems in schools all the...

    I agree and see these problems in schools all the time from design engineer. As much as I blame them for poor design alot does come down o price. If you want to truly have a standalone system like...
  41. Replies
    14
    Views
    1,961

    The code these pre-built applications generate is...

    The code these pre-built applications generate is pretty much unreadable unless you developed the software. It is VERY VERY hard to understand to make small modifications and if you want to use it to...
  42. Replies
    9
    Views
    988

    As much as I would like to bash JCI, this is a...

    As much as I would like to bash JCI, this is a Ford issue with the Chicken Tax. They replace the glass with steel after it gets into the US to avoid paying extra tax. They also shred the seats and...
  43. This valve does floating control with 120V ac...

    This valve does floating control with 120V ac pulse open or close after it is powered to low fire on initial power up. i have wired them to power flame burners before but I have never wrote the...
  44. Replies
    5
    Views
    1,221

    in 3.7 there are new password requirements that...

    in 3.7 there are new password requirements that are turned on where before they weren't by default. I'm not sure if an old password is still valid or not. I would try logging in to the Jace as your...
  45. Replies
    5
    Views
    1,221

    Not exactly sure but does the account you have...

    Not exactly sure but does the account you have sharing data between the Jace and the supervisor have permission to write/invoke in the Jace where the points reside?

    -Jeremy
  46. Replies
    161
    Views
    31,998

    need your e-mail address in your profile to send...

    need your e-mail address in your profile to send you stuff.

    -Jeremy
  47. Replies
    5
    Views
    729

    The alarm screen displays either the point name...

    The alarm screen displays either the point name or system point name depending on the user account logged into the system. In the Apogee world the system names is what links everything together.
    ...
  48. Replies
    2
    Views
    539

    If you mean a 540-100 VAV TEC on an FLN then you...

    If you mean a 540-100 VAV TEC on an FLN then you need WCIS to see the 99 points report and adjust the settings. These are a pre-programmed device and there is no internal logic to adjust, just set...
  49. Replies
    2
    Views
    755

    For the KMD protocol your only option is...

    For the KMD protocol your only option is TotalControl as a front end from KMC. There is no other option and even as a KMC distributor I wish there were.
    TotalControl can communicate both KMD, BACnet...
  50. Thread: Max Masters

    by kc2dnw
    Replies
    29
    Views
    3,070

    They exist within the the Echelon chip which is...

    They exist within the the Echelon chip which is only modifiable by they copyright owner. All networks have these parameters, they are a function of the hardware. It is the protocols choice whether to...
Results 1 to 50 of 121
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event