Search:

Type: Posts; User: HeatMaker

Search: Search took 0.00 seconds.

  1. Replace the tube. You will have to check with...

    Replace the tube. You will have to check with your AHJ, but I believe plugging is a temporary repair. Temporary repairs are usually only allowed for 30 to 90 days, depending on your local laws and...
  2. Replies
    3
    Views
    5,212

    I have downloaded a couple of service manuals...

    I have downloaded a couple of service manuals online, and I have found them to be more helpful then Daikin tech support.

    http://www.daikinac.com/commercial/docsOverview.asp?sec=docs
  3. Replies
    4
    Views
    1,257

    I have seen alot of newer York economizer module...

    I have seen alot of newer York economizer module failures recently. If you unhook the 24V coming into the module, it will act the same as if the economizer was not there, and the unit should run just...
  4. Replies
    2
    Views
    1,626

    Call your local Trane sales office and ask them...

    Call your local Trane sales office and ask them to email the IOM for your model sensor.
  5. Replies
    2
    Views
    762

    Maybe a RTRM board issue? I have had quite a few...

    Maybe a RTRM board issue? I have had quite a few YCD board failures recently. Is there another unit you could swap the board with to verify? The issues I have seen recently are random failures, heat,...
  6. Replies
    24
    Views
    3,174

    I use Simple Green HD, it's actually purple. I...

    I use Simple Green HD, it's actually purple. I have also used Grease Off with pretty good results.
  7. I had a walk in freezer go down at 9 pm once, the...

    I had a walk in freezer go down at 9 pm once, the customer did not want to pay overtime to repair it. I returned at 7 am the next morning and it had warmed to 9*F. By the time the repair and proper...
  8. Replies
    4
    Views
    1,051

    I was putting a 350HP Cleaver back online after...

    I was putting a 350HP Cleaver back online after an overhaul. I went to open the fuel valve but it was sticking, so I leaned into it pretty hard. When the valve opened, it dropped fuel pressure to the...
  9. Replies
    4
    Views
    567

    We have had many Smith 28 section failures in our...

    We have had many Smith 28 section failures in our shop. They seem to be going through the same troubles Burnham had a few years back.
  10. Replies
    8
    Views
    3,905

    I have never had to use a pressure enthalpy...

    I have never had to use a pressure enthalpy chart. I guess I have yet to be in a situation where I could use it.
  11. SAFETY, SAFETY, SAFETY! Pay attention to your...

    SAFETY, SAFETY, SAFETY! Pay attention to your surrondings. Like many have already said, there is alot more stuff that can harm you in the commercial field. Be very thorough. I have been in your exact...
  12. Thread: Multitool

    by HeatMaker
    Replies
    26
    Views
    3,240

    I carry a Leatherman Super Tool 300 and a folding...

    I carry a Leatherman Super Tool 300 and a folding Husky utility knife. I bought the 300 after I wore out my 200. The Super Tool is a tough tool!
  13. Replies
    8
    Views
    1,321

    It is not uncommon to find larger boilers...

    It is not uncommon to find larger boilers downfired a little bit. I think the ECT is a Peerless right? I have seen many Peerless boilers run in the 300-400 net stack range with no signs of trouble.
  14. Replies
    4
    Views
    640

    Thanks fellas. I'm going to pick up some...

    Thanks fellas. I'm going to pick up some adapters, just thought I'd ask first.
  15. Replies
    4
    Views
    640

    Cable building

    Is it possible to build a cable (usb to rj12) to connect to a Trane system? I have varitrac software on a new pc without a db9 connector. Can you bypass the db9 all together and just go straight usb...
  16. Thread: Hello

    by HeatMaker
    Replies
    1
    Views
    778

    Hello

    Just wanted to say hello. I have been in the trade scince early 2004. I now work for a company based in southern Maine, with offices across the state. I have already been searching through the forum,...
Results 1 to 16 of 16
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event