Search:

Wow. It has been a very long time since I have been on this site. I remember this thread in its infancy. What an inspiring individual Brett was. His positive outlook through all of his trials was...

Heavy duty prayers on their way up for you and your family Brett. You have been a true inspiration. God Bless.

These baffles are made of a heat resistant felt type material, with wire supports

Evidently there is a "pin" that locks them into position, assume it was never assembled properly and over time they re-oriented themselves.

Thanks to all that responded, especially dandyme for the email.

But here is one to put into your tool box. The final solution to the issue was.........wait for it......the BAFFLES!!! It...

Like you, I have been busy as well. Spent the weekend at a large plant here repairing split heating coils in a MUA. Good Times!!:cheers:

Hello Brett,
Been quite a while since I have checked in on you. I will have to spend some time catching up on the posts but it sure is great to see you still carrying on!!! Have a great evening.

Thanks TB! Kinda where I was goin with this. Was hoping for a miracle cure......lol. How have you been? I haven't been here in quite a while.

SN 940100877L No heat....

Had one today tripping limit. Found a failed fire damper. One more thing to look for.

Didn't want the pipe hanger to chafe:gah:

Separate high limits for first and second stage? Hmmmmm. Cant say I have seen that before, doesn't mean that it doesn't exist, but I don't know why that would be. Same heat exchanger compartment,...

I cut it out and pro press. Done:cheers:

Just curious, was the quote for the same repair you did? And I agree about the cats:gah:

Layers upon layers, a bit confining but necessary. Had to go up on a roof during the last "vortex" in minus 12 deg f. actual. Wind blowing like a bugger, snow knee deep. Large building in an...

Went there this A.M. and fired up furnace. Checked manifold pressure, 4.25" WC. Adjusted to 3.5. Definitely not the cause of problem. Let furnace run and monitored temp at roll out switch. ...

Lol. Guess that I didn't think that through Coope. Between the phone ringing and trying to respond to you guys, my thought process was not at its peak. I am leaning more toward gas pressure, ...

Lol!!!! Fixed some frozen pipes this morning. Man, you guys got hammered. Minus 13 actual temp here yesterday, so yes, I have been busy too. Not complaining though, busy is good, it is the...

Return temp 70 degrees, supply temp 102 degrees. If anything a little low. Also I don't know where the temps were actually taken at.

No, but that was I thought that I had, which is why I know the motor is original. I thought that maybe someone changed the motor out over the summer and put the wrong one in. How you been qwerty?

Thanks guys, air filter is clean, and just to put your mind at rest , this guy is a retired 636 service fitter, repaired commercial and industrial stuff for many years so is familiar with...

thanks for the responses. WMT, the furnace is cycling normally, approximately 8 minutes per cycle, leading me to believe that there is no blockage in supply. COOPE, anything is possible...

Hey pros, I just received a call from a friend whose father-in-law is having problems with his furnace. The father-in-law is a retired 636 service fitter. Has an Arcoaire furnace, I do not have...

Hilarious!!!!

They may have felts in them, whats the harm?

Just to let you know, all of us still from time to time come across our "firsts". That is the beauty of doing what we do, one never stops learning.

I have no advice to offer on this repair. Just wanted to say, job well done. Your journeyman sounds like a real joker. Keep your attitude of troubleshooting, not part swapping. It wont be...

How old is this unit. Did you check the heat exchanger? Not familiar with this particular unit, but I wouldn't think there would be that much different about it. Hi temp limit? Stack switch?

As it should, you have no humidity control. Replace the humidistat.

X2

My opinion? Run as fast as you can. I strictly do commercial/industrial, however I have known guys that have worked hourly plus commisssion. If you have no scruples, this may be for you. Lots o...

I believe that I shed a tear there.

Be sure to use a center punch on the snapped off portion of the bolt. Be sure that you are as close to center as possible. EZ out the snapped off bolt. Am not familiar with the sight glass...

56 percent silver and flux, does a great job, nice flow

Sounds like there is a problem. Even with a dead battery, with unit plugged in to the wall charger, it should operate, mine does.

I have been doing this for a long time and I still am learning

Seriously? Good luck

I had a problem once, similar in nature, on a three door display freezer. Changed the fan delay switch and unit took off. Next day get a call, not working again. Arrive on site, it is working...

I assume that you have not done much reefer work. The answer to your question is yes.

I don't text ever, hate it. But that is one horrific video!!!

Afternoon Brett and all.

I have no words of wisdom to offer. I do however wish you the very best in your new posistion, and I have no doubt that you will be a great boss. I know that I for one would be happy to be a...

Me fears that we will never know.

.

I am betting on the blower motor.:.02:

I second that opinion!!!!! I second that opinon!!!!! Oh crap, it must be contagious, I think I'm repeating myself too.:gah:

Not trying to discourage you, just give you some things to think about.

One thing about trading hot days on the roof. Imagine a hot kitchen in the middle of summer, ovens, friers, grills, etc....

LMAO Although sometimes you'd rather not have gotten that upskirt:gah:

I did restaurant equipment repair for 12 years. You will see some of the nastiest stuff you could ever imagine. Have to work on a oven that needs to come out of its resting place to be repaired? ...

I see that you have the same romantic inclinations as me. The card that I bought my wife read:


For Valentines Day, I just wanted to say those THREE WORDS that you can't hear me say...

LMAO!!!!!!!