# Single phase and Three phase motors

Show 40 post(s) from this thread on one page
Page 1 of 2 12 Last
• 05-15-2013, 12:36 PM
RIEIO
Single phase and Three phase motors
im a college student studying HVAC, and I was really trying to understand the difference between single phase and three phase motors in the hvac industry
• 05-15-2013, 11:55 PM
jayguy
that is a very loaded question. basically, a single phase motor uses 2 lines of incoming power and a three phase motor uses 3 lines of incoming power.

a single phase motor is usually used for low horsepower applications where as 3 phase motors are used for larger horsepower applications.
• 05-16-2013, 09:13 PM
ryan1088
Were you looking for something more specific? Jay gave a good answer for how vague your question was.
• 05-16-2013, 09:20 PM
Core_d
3phase is more efficient although initial cost is more. This video may help http://m.youtube.com/watch?v=07uXnc1C5CA
• 05-16-2013, 10:01 PM
DDC_Dan
Quote:

Originally Posted by RIEIO
im a college student studying HVAC, and I was really trying to understand the difference between single phase and three phase motors in the hvac industry

The motor used is matched to the building power available, so a commercial unit installed where 3-phase power is available will contain 3-phase motors, while a residential unit will have single phase motors.

The big difference between the two motors is that 3-phase motors use the phase rotation of the incoming power itself to create the rotating magnetic field, while single phase motors cannot. They must use an additional component (such as a capacitor) to create the necessary phase shift for starting, and in some cases running as well. This creates additional complexity and points of possible failure for the single-phase motor.

Very cool old video btw core_d.
• 05-17-2013, 08:53 AM
VTP99
.
• 05-17-2013, 09:20 AM
timtanguay
Also, 3phase motors have poles mechanically separated by 120 degrees, which coincides with the phase angle offset of 120 degrees per phase. 3 phase motors do not have starting aids (relays and caps) because the starting torque is so much greater than single phase.

Sent from my HTC One S using Tapatalk 2
• 11-11-2013, 10:32 PM
Joe Harper
Quote:

Originally Posted by timtanguay
Also, 3phase motors have poles mechanically separated by 120 degrees, which coincides with the phase angle offset of 120 degrees per phase. 3 phase motors do not have starting aids (relays and caps) because the starting torque is so much greater than single phase.

Sent from my HTC One S using Tapatalk 2

Actually they do have relay systems to start them. Look up wye delta starter.
• 12-15-2013, 05:15 PM
genman
Just hang on Rieo... If your in college they will explain that to you - it might be coming later in the course. It's been my experience that college explains things to such a depth that alot of it is useless. So if they don't explain that basic difference in an ac/refer education that you are paying thousands of dollars for... sue the crap out of them and get your money back bud...
• 12-15-2013, 07:22 PM
Core_d
Quote:

Originally Posted by genman
Just hang on Rieo... If your in college they will explain that to you - it might be coming later in the course. It's been my experience that college explains things to such a depth that alot of it is useless. So if they don't explain that basic difference in an ac/refer education that you are paying thousands of dollars for... sue the crap out of them and get your money back bud...

Genmen, good to see in the forum. You have dug up every thread I have been a part of in the electrical forum. Perhaps you could start your own thread either learning or teaching.
Hope to see you in the future.
• 10-23-2015, 12:44 PM
richardrich44
Well, as i know 3phase motors are for industrial usage, factories...
And with a single phase motor you can power home equipment
• 11-29-2015, 08:22 PM
YingGiang
Good thread! Always someone post something that I can learn from.

Sent from my iPhone using Tapatalk
• 11-29-2015, 09:05 PM
BBeerme
:angel:
Show 40 post(s) from this thread on one page
Page 1 of 2 12 Last